1.1Two lower rod openings
Two laterally offset saddles receive the rods as the body is lowered over them. A captive swing gate closes each saddle from below, and a screw in the gate presses the rod against the saddle roof.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two laterally offset saddles receive the rods as the body is lowered over them. A captive swing gate closes each saddle from below, and a screw in the gate presses the rod against the saddle roof.
Opposed blind bores in a solid sleeve receive the rod ends up to a central stop. A radial set screw in each bore presses its rod against the bore wall.
A machined body carries two saddles on opposite faces of a solid web. A separate screw and pressure pad at each saddle press its rod against the saddle floor, and the web transfers load between the saddles.
An eccentric cam turns on an external pivot and pushes a crossbar against two hinged jaws. Each jaw rotates toward its fixed saddle and grips one rod, and a captive screw holds the cam in its closed position.
A concave surface machined into the body supports the second rod. A shared slider carries an inclined face that presses the second rod down against the seat and a second face that clamps the first rod against its channel wall.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A connector body joins two solid frame rods on adjacent conveyor guard panels. Laterally offset channels receive one rod from below and the other from above. A sliding wedge occupies the recess between the channels, supports the upper rod, and bears against the lower rod. A threaded closure in the upper socket presses the upper rod against the wedge, which drives the lower rod into its seat.
An eccentric cam on a transverse pin replaces the threaded closure in the upper rod channel. Opposed bores in the socket walls support the pin, and the cam lobe bears on the upper rod. Rotation of the cam drives the upper rod against the locking member spanning the recess, and the locking member presses the lower rod into its seat. The cam rotates past its point of maximum lift and rests against a stop, while a spring detent holds it in the closed position.
The lower channel receives a 6.0 mm rod, and the upper channel receives a 4.0 mm rod with its centerline offset laterally by 8.0 mm. The corresponding channel mouths measure 6.2 mm and 4.2 mm across. A locking member spans the recess and carries concave contact surfaces with radii of 3.0 mm for the lower rod and 2.0 mm for the upper rod. Tightening the closure in the upper socket presses the smaller rod against its contact surface and drives the locking member against the larger rod.
The upper and lower channel axes form a 15 degree angle in plan view, and their centerlines are separated laterally by 10 mm at the midpoint of the body. Each channel provides an 8 mm long rod seat, and the channels open on opposite faces of the body. A guided locking member spans the recess and carries two curved contact surfaces machined along the respective channel axes. The closure loads the upper rod into its contact surface and shifts the locking member toward the lower rod.
An external lug on the connector body carries a crosslink mount beside the upper channel socket. The mount uses a vertical threaded bore and a flat bearing face to secure the slotted end of a transverse crosslink. The opposite end of the crosslink clamps to a longitudinal rod on the other side of the fixation construct. The closure loads the two rods through the locking member in the spanning recess, and a separate screw secures the crosslink after its lateral position is set.
A bench fixture holds the connector body and seats two test rods in the opposite-facing channels. A motorized driver engages the threaded closure, while a torque transducer and rotary encoder record tightening torque and angle. Software identifies initial seating from a sustained rise in torque, then advances the closure to the programmed test torque. The software records the torque and angle trace and flags cycles in which the rotation after seating falls outside the programmed range.
A titanium alloy body has two semicylindrical saddles with parallel, laterally offset axes. The first saddle opens downward, the second opens upward, and a milled slot connects them through the body.
A transverse pin retains a rocker in the recess, with one arm projecting into each rod channel. The second rod seats on a concave pad on the upper arm and rotates the rocker downward, which drives the lower arm against the first rod.
Flat guide faces in the recess constrain a locking block to translate, with one end projecting into each rod channel. The second rod seats on the block's upper pad and pushes it downward so that a ramp at the lower end presses the first rod against its channel wall.
A threaded plug turns into an internally threaded socket at the opening of the second rod channel. A hexagonal drive recess receives the driver, and the plug's flat tip presses the second rod against the locking member.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The inwardly extending shoulder 48 formed by lower portion 39 of diaphragm 33 is received in a groove 59 in valve plug 53, and is securely affixed by a snap-on retaining ring 61. As best illustrated in FIG. 5B, retaining ring 61 includes a lower tapered portion 62 having an inwardly extending shoulder 63 that engages with an outwardly extending shoulder 64 on plug 35.A · US 7,232,107 B2 · ¶ 40
Valve closure member or plug 35 is slidably mounted in valve body passage 31, and carries an O-ring 56 at its bottom end which engages with valve opening 29 to close the valve.A · US 7,232,107 B2 · ¶ 39
A gas outlet port 6 can be either unobstructed by a closure plug 32 as shown, or can be obstructed by the closure plug 32, as shown in FIG. 4.B · US 10,648,584 B2 · ¶ 23
An empty cell means only that no passage was reproduced there.
Valves according to the invention have broad utility but are particularly useful in underground sprinkler and irrigation systems, where low part fabrication and assembly costs must be balanced against the need for designs which provide high reliability and durability.A · US 7,232,107 B2 · ¶ 4
A valve according to this invention can be made quite small, yet exhibits notably low pressure drop.A · US 7,232,107 B2 · ¶ 7
Mechanical type earthquake valves can be accidentally activated if the valve body is bumped into, or if a large truck rumbles down the street and causes enough shaking to dislodge the ball sitting on its pedestal, causing it to roll down and shut off the gas.B · US 10,648,584 B2 · ¶ 7
A timing circuit delays the activation of the closure plug to make sure that the motion has been caused by an earthquake and not by an accidental brief jarring action.B · US 10,648,584 B2 · ¶ 8
patent.fyi, US 2026/0354870 A1, claim 1, first published 2026-11-19T04:53:05-05:00, https://patent.fyi/US20260354870/, SHA-256 fa4942a78d79b18de9f3d836c9166939587dad5e1d95750039b381c9467bf4f9