1.1Resistive heating at the tip
Two insulated conductors carry current to a nichrome coil mounted inside the distal tip. An electrically insulating aluminum nitride sleeve conducts heat from the coil to the metal tip.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two insulated conductors carry current to a nichrome coil mounted inside the distal tip. An electrically insulating aluminum nitride sleeve conducts heat from the coil to the metal tip.
A pump drives warm water through an inner supply tube into a sealed chamber at the tip. The water transfers heat to the chamber wall and returns to the heated reservoir through an annular passage.
An inner capillary carries pressurized argon to a small orifice at the distal end. The expanding gas absorbs heat from the metal tip and flows back through an annular exhaust passage.
A proximal collimating lens aligns the beam with the center of a rigid bore, and the beam clears the bore walls along its path. A dark ceramic surface on the inside of the metal tip absorbs the beam and transfers heat into the tip.
Insulated wires feed a near-infrared diode mounted immediately behind the tip in a sealed cavity. The diode emits across a short gap onto an absorptive inner surface that conducts heat into the tip.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A hollow stainless steel sampling needle uses a circulating refrigerant to freeze a small plug of liquid food against its distal end. A fixed optical fiber inside the needle directs light onto an absorbing surface on the inner face of the tip. At the discharge station, the refrigerant valve closes and the source illuminates the tip to thaw the contact layer so the plug drops into a collection cup.
A hollow metal capillary with a reflective inner coating replaces the solid optical fiber. A lens couples light from the source into the proximal opening, and the capillary carries the light by internal reflections to an absorbing surface on the back of the tip. A sealed sleeve around the capillary keeps coolant out of the optical bore and leaves an annular passage for coolant flow.
A bench probe uses a 400 µm core optical fiber with its end face held 1 mm from a flat absorber bonded to the inner face of the needle tip. A pulse driver delivers 200 ms illumination pulses at 1 Hz for 10 seconds after the coolant valve closes. A thermocouple on the outer tip records temperature at 100 samples per second during each pulse train and the subsequent cooldown.
Four 300 µm core fibers connect a shared radiation source to four cryogenic needles, with one fiber facing the inner tip surface of each needle. A motorized mirror at the source aligns the beam with one proximal fiber face at a time. The source illuminates each port for 250 ms and turns off while the mirror moves, completing a four-port scan in a 2 second cycle.
A cryogenic needle with an internal heating fiber mounts in the biopsy guide of an ultrasound transducer. The guide keeps the needle shaft in the imaging plane while coolant freezes the surrounding tissue. After coolant flow stops, the fiber directs radiation to the inner face of the tip while the transducer images the visible boundary of the frozen region during thawing.
A miniature thermocouple bonds to the inner wall of the needle next to the surface illuminated by the optical fiber. A controller reads the thermocouple and adjusts source power with a proportional-integral loop to hold the tip at a programmed temperature. An open thermocouple circuit or a measured temperature above the configured limit disables the source driver.
A coupling lens launches 980 nm light from a laser diode into a multimode silica fiber with a 200 micrometer core. The flat distal end directs light onto an absorptive coating on the inside face of the tip.
A dielectric-coated bevel at the distal end of a silica fiber reflects the beam sideways near the tip. An absorptive band on the inner wall intercepts the beam and heats the surrounding metal.
A current driver switches an 808 nm laser diode in 100 millisecond pulses, and a coupling lens launches the light into a multimode fiber. A thermocouple bonded to the tip provides feedback that the controller uses to adjust the interval between pulses.
A silica fiber carries near-infrared light to a short distal section with a scattering surface that releases light along its length. A cylindrical ceramic absorber around that section collects the light and conducts heat into the metal tip.
patent.fyi, US 2026/0354882 A1, claim 1, first published 2026-11-19T05:29:29-05:00, https://patent.fyi/US20260354882/, SHA-256 c526ec6982c1e3f32a459d417f7d5c3315964a4b6e844009a70d4f827ce6c0ad