1.1Frame mounted applicator
A locking arm holds the head against the treatment site through a skin contact ring. A motorized linear stage advances and retracts the needle array, and a cable connects the electrodes to a pulse generator.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A locking arm holds the head against the treatment site through a skin contact ring. A motorized linear stage advances and retracts the needle array, and a cable connects the electrodes to a pulse generator.
A molded polymer carrier holds the needle array and is ultrasonically welded into the applicator housing. An internal slider advances the carrier, and an external cable connects the applicator to a reusable generator.
Conductive bands lie beneath a thin conformal dielectric, and thicker insulating collars cover the shaft between bands. An alternating voltage drives displacement current through the dielectric at the bands, where the thinner coating provides greater capacitance to the tissue.
A circular carrier holds parallel needles at a common radius with equal spacing between neighbors. The generator switches between adjacent bipolar pairs around the ring and delivers each pulse through tissue between the paired electrodes.
A common bus connects all needles to one generator terminal, and a conductive annulus around the insertion area connects to the other terminal. Current passes between the exposed needle bands and the annulus through the surrounding tissue.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A detachable cartridge holds a rectangular array of insulated needles with exposed shaft bands aligned at a common depth. A fixture lowers the array into a conductive gel block until a mechanical stop aligns the bands with a selected gel layer. A differential alternating-current source drives neighboring needles in opposite phase along both rows and columns. Embedded temperature probes record the response in the selected layer and in the layers above and below it.
Thin alumina sleeves replace the insulating coating on the shaft of each conductive needle. Two sleeves sit on opposite sides of an exposed metal band, and a pointed ceramic cap covers the distal end. A cartridge datum sets the axial position of each needle so the exposed bands share a common plane. Two interleaved conductor networks connect adjacent needles to opposite terminals of a differential source.
A detachable cartridge carries 24 needles in four rows of six, with a center-to-center pitch of 1.0 mm along each row and 1.5 mm along each column. Each needle has one exposed shaft band located at the same axial position relative to the cartridge face. Alternating positions along both axes connect to opposite electrical terminals. The unequal pitches create shorter electrode gaps along the rows than along the columns.
A linear ultrasound probe mounts beside the handpiece on an angled bracket that directs its imaging plane through a central row of the cartridge. A coupling pad fills the gap under the probe while leaving the cartridge face clear for needle travel. Calibration in a gel block registers the needle trajectories and exposed-band depth to the ultrasound image. The display overlays the calibrated band positions on the cross-sectional image during placement.
A handpiece collar forms an annular vacuum chamber around the detachable needle cartridge, with an elastomer gasket sealing the chamber against the skin. Shallow radial channels connect the chamber to a regulated vacuum line while a perforated support plate sets the local skin surface position. The needle array advances through clearance holes in the plate to a fixed stroke that sets the exposed-band depth. A valve vents the chamber after the array retracts.
An analog switch matrix routes individual needles to an impedance measurement circuit during a diagnostic cycle. A controller applies a low-amplitude alternating test signal across each horizontal and vertical neighboring pair and derives impedance from the measured voltage and current. It compares the results with a calibrated range and maps out-of-range pairs to their row and column positions. The output stage stays disabled until a repeated scan places all measured pairs within range.
A geared motor turns a lead screw inside a molded handpiece housing. A guided carriage translates screw rotation into axial needle motion, and a position sensor tracks carriage travel.
Two lugs on the cartridge enter matching slots in the handpiece and rotate into retaining pockets. A keyed stop sets the final angle, and spring contacts press against cartridge pads when the mount seats.
A conformal polymer film covers each stainless steel needle, including its distal end. Laser ablation removes the film from two circumferential bands along the shaft and leaves insulation between the bands and on either side of them.
A four-by-four needle grid connects to two generator terminals so that each pair of immediate neighbors in a row or column connects to opposite terminals. Each needle carries an exposed band at the same distance from the carrier face, which places the bands at a common depth when the face seats against the skin.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The one or more electrodes may comprise one or more hooks, one or more grabbers, one or more blades, one or more knives, one or more serrated blades, one or more probes, one or more biopsy tools, one or more robotic tools, one or more pincers, one or more electrosurgical pencils, one or more forceps, one or more bipolar forceps, one or more coagulation devices, one or more irrigation devices and one or more imaging tools.B · US 2018/0238776 A1 · ¶ 36
The first needle 16 is captively secured in the handpiece bore 8 between the ring 10 and the second axial end 6 of the handpiece 2. The second needle 18 is coaxially arranged within and fixed to the first needle 16.A · US 2017/0119468 A1 · ¶ 19
Pulsed waveforms and duty cycles may be used for both cut and coagulation modes of operation by inducing electrical plasma along the cutting edge(s) of a thin insulated electrode.B · US 2018/0238776 A1 · ¶ 368
Other embodiments are also contemplated wherein the snare electrode may comprise a bipolar device such that electrical current does not flow through the patient's body.B · US 2018/0238776 A1 · ¶ 380
An empty cell means only that no passage was reproduced there.
These tapered optical fibers are helpful for providing wider illumination of a patient's eye as compared to a flat-ended optical fiber.A · US 2017/0119468 A1 · ¶ 6
Accordingly, there is a need for a microsurgical instrument that reduces residual motion between sub-components and simplifies construction of the handpiece, while also shielding glare from a wide angle optical fiber probe.A · US 2017/0119468 A1 · ¶ 7
Rapid evaporative ionisation mass spectrometry (“REIMS”) may be used for the real time identification of tissues, e.g., during surgical interventions.B · US 2018/0238776 A1 · ¶ 3
This sampling technology allows surgeons to more efficiently resect tumours intra-operatively through minimizing the amount of healthy tissue removed whilst ensuring that all the cancerous tissue is removed.B · US 2018/0238776 A1 · ¶ 4
patent.fyi, US 2026/0354890 A1, claim 1, first published 2026-11-19T05:29:29-05:00, https://patent.fyi/US20260354890/, SHA-256 83bb7eb70c159afe4b6c069f1c8d1921d486b571096e1b95d8bfc1e3c1b34000