1.1Dye applied directly to skin
A porous felt tip meters dye solution onto the skin in the shape of a dot or cross. The solvent evaporates and leaves a colored mark on the outer skin layer.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A porous felt tip meters dye solution onto the skin in the shape of a dot or cross. The solvent evaporates and leaves a colored mark on the outer skin layer.
A molded holder captures the edges of a printed marker disc and slides onto a woven elastic band. A buckle sets band tension, and a textured silicone pad under the holder limits sliding on the skin.
A paper marker carries a dry hydroxypropyl cellulose coating on its underside. A damp applicator hydrates the coating before placement, and evaporation leaves a dry film that holds the marker against the skin.
A printed 4 mm disc uses aluminum foil laminated between polymer films to restrict water vapor passage. The disc covers about 13 mm² of skin, and surrounding uncovered skin remains exposed to air. The disc is peeled off after the procedure.
A transparent polyurethane film carries a cross printed with a fluorescent dye in a clear binder. A handheld 365 nm lamp excites the dye and makes the cross emit visible light.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A matte, opaque, vapor-permeable polyurethane film carries a removable acrylic pressure-sensitive adhesive on its underside. A placement crosshair and a mount identifier are printed on the exposed face. The marker presses onto a sealed display deck, aligns the mount during installation, and peels away by a folded pull tab once the mount is fixed.
A silicone pressure-sensitive adhesive replaces the continuous adhesive coating on an opaque, vapor-permeable polyurethane film. A rotary screen deposits separated adhesive dots on a release liner, and a nip laminates the film to the dot pattern. The dots hold the marker against skin under light pressure, and the gaps leave portions of the film exposed on the skin-facing side for vapor transport.
Two circular markers, each 8 mm in diameter, sit on a common transfer carrier with their centers 30 mm apart. Each disc consists of an opaque, vapor-permeable film in contact with a pressure-sensitive adhesive and carries a printed center dot. The operator removes the shared release liner, presses both discs onto the skin through the carrier, and peels away the carrier to leave two reference points at the set spacing.
Three adhesive markers carry distinct black fiducial patterns printed on an opaque, vapor-permeable film. The markers adhere at separated points on intact skin within the field of a calibrated stereo camera pair. The registration software identifies the patterns, triangulates their centers, and uses the three noncollinear points to define a local coordinate frame for the surface scan.
A die-cut skin marker and a separate specimen-container label sit side by side on a release liner. The skin marker consists of an opaque, vapor-permeable substrate in contact with a pressure-sensitive adhesive, and both pieces carry the same printed identifier. The operator places the marker beside the collection site and applies the matching label to the specimen container. A barcode reader enters the identifier into the specimen tracking system.
An encoder triggers a calibrated reflectance camera as a continuous film and pressure-sensitive adhesive laminate passes over a split black-and-white backing in a liner-free inspection span. The software divides the reflectance measured over the black backing by the reflectance measured over the white backing to calculate opacity for each inspected web segment. It records segments below 65% and sends their encoder positions to the downstream die cutter for rejection after the release liner is laminated.
A thermally bonded web of continuous polyester filaments carries the printed mark on its outer face. The web bends with the skin, and the bonded filament junctions hold the cut edge together.
A rotary screen deposits a waterborne acrylic pressure sensitive adhesive in spaced dots directly on the substrate. Drying removes water from the coating, and light finger pressure brings the dots into contact with the skin.
A low-modulus silicone pressure sensitive adhesive is cast and cured directly on the inner face of a flexible polyurethane substrate. The layer deforms under finger pressure to make contact across fine skin contours.
A hydrophilic polyurethane film transports water vapor through the polymer and contains dispersed titanium dioxide to increase opacity. Tests on the finished marker verify water vapor transmission of at least 100 g/m2/day and opacity of at least 65%.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The present invention also relates to a wood panel comprising: an underlying engineered wood board having upper and lower surface layers and a core layer; and a nonwoven polyester water vapor-permeable layer having a moisture vapor transmission rate of less than 5 perms attached to the upper surface layer.A · US 2007/0178793 A1 · ¶ 7
Optionally an adhesive may be used to bond the water vapor-permeable layer to the engineered wood board. This adhesive is preferably selected from phenolic, epoxy, and polyurethane resins, which are described above.A · US 2007/0178793 A1 · ¶ 19
The polymeric material may comprise a pressure sensitive acrylic adhesive film such polyester (PET), polymethylinethacrylate (PMMA), or a thermoplastic coating, polyamides, amorphous polyester resins, acrylic resins, or any other material that provides sufficient moisture vapor transmission and has an appropriate surface energy.B · US 7,279,831 B2 · ¶ 20
The composite as claimed in claim 1, wherein said water vapor permeable composite has an overall moisture vapor transmission rate of greater than one gram/100 sq. inches for a 24 hour period at 100° F.B · US 7,279,831 B2 · claim 2
An empty cell means only that no passage was reproduced there.
This panel construction provides excellent protection against water penetration, particularly where adjacent panels meet to form a sea; and yet because the barrier layers are attached during manufacture, the additional step of applying barrier layers such at Tyvek during building and construction is avoided.A · US 2007/0178793 A1 · ¶ 3
Given the foregoing, there is a continuing need to develop an engineered wood board having one or more applied barrier layers, which is capable of being pressed by the use of steam-injection.A · US 2007/0178793 A1 · ¶ 5
There is a need therefore, for an electroluminescent material whose performance is not dependent on the presence or absence of water vapor from the material.B · US 7,279,831 B2 · ¶ 5
Water vapor, therefore, may pass through the composite without adversely affecting the operation of an electroluminescent device that includes a composite of an embodiment of the invention.B · US 7,279,831 B2 · ¶ 6
patent.fyi, US 2026/0354928 A1, claim 1, first published 2026-11-19T06:07:06-05:00, https://patent.fyi/US20260354928/, SHA-256 58514a5dd5cefb7dba2b69e27a98e4cbbbac4acfa2d84c4b44cbd7d20d74df48