1.1Spherical head on the stem
The elastomer gasket expands as it passes over the widest part of the head during seating. It contracts around the narrower stem below the head and expands again when the overdenture is lifted.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The elastomer gasket expands as it passes over the widest part of the head during seating. It contracts around the narrower stem below the head and expands again when the overdenture is lifted.
A matching taper on the underside of the housing centers the housing as the overdenture seats. The tapered surfaces carry seating loads while the gasket grips the stem.
An internal shoulder in the housing supports the outer edge of the gasket and maintains axial clearance above the abutment. The inner lip flexes over the head and contracts around the stem.
The projection enters through the lower housing opening and passes through the gasket into a recess beneath the roof. The gasket contracts around the stem while the roof clears the projection at full seating.
The tissue-facing denture base sets the seated height and transfers compressive loads to the supporting tissues. The gasket extends below the housing to contact the abutment top and engages the stem to resist lifting.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Four studs on the enclosure rim each have a flat base, a narrow stem, and a broad rounded head. The cover carries four open ring housings, each with inward ridges that capture an elastomer gasket. Pressing the cover onto the rim expands each gasket over its stud head and seats it around the stem, while the head remains visible through the housing opening. Pulling the cover away releases the gaskets from the studs while the housings retain them.
A split acetal snap ring replaces the elastomer gasket in the open housing. The ring has a beveled inner entry edge and sits in an annular recess between inward housing ridges, with radial clearance for expansion. The rounded head spreads the ring at its split during insertion. After the head passes, the ring returns around the stem and its upper face bears against the underside of the head under withdrawal load.
A threaded retaining collar replaces the inward ridges in the gasket housing. The gasket sits against an internal shoulder, and the collar threads into the abutment-facing end of the housing. The collar bore clears the rounded head and overlaps the outer rim of the gasket, leaving the inner rim free to expand over the head and recover around the stem. With the overdenture removed, a pin wrench engages two face holes in the collar so the gasket can be replaced.
A bench fixture uses a 10 mm diameter flat base, a 4 mm diameter stem, and a 6 mm diameter rounded head. A gasket with a 3.8 mm inner diameter and a 7.5 mm outer diameter sits in an open housing with a 9 mm outer diameter and a 6.5 mm clear opening. Inward ridges bound an annular pocket with clearance for outward gasket expansion as the head passes. A force gauge drives the housing axially onto the fixture and then withdraws it at 20 mm per minute to record peak seating and release forces.
A rigid screw-retained bar spans two implant abutments and carries two upright studs on flat seating pads. Each stud has a narrow stem and a broad rounded head, and the overdenture carries a matching open housing with a captive gasket. The two stud axes are parallel, so both gaskets pass over their heads along a common insertion path and recover around their stems. The bar transfers the attachment loads to the two implant abutments.
A three-dimensional scan records the rounded heads and the exposed flat seating surfaces of the abutments. Dental design software fits a circle to each head perimeter and a plane to its seating surface, then uses the circle center and plane normal to locate the matching housing pocket in the overdenture base. The software checks each head and housing for collision along the planned insertion path and exports the base for milling. A positioning jig holds the gasket housings at the calculated depth and orientation while bonding resin cures.
A titanium abutment seats against the implant platform. A central screw draws the abutment against the implant and holds it in axial compression.
The abutment and stem are turned from a single titanium blank. The stem rises from the machined abutment top and has a cylindrical outer surface where the gasket contacts it.
A blind threaded bore opens through the underside of the projection and engages a male thread at the top of the stem. Tightening the projection seats its underside against an annular shoulder on the stem.
A titanium housing with a 6 mm outside diameter surrounds a silicone gasket with a 5 mm outside diameter in the free state. The cylindrical gasket pocket centers the gasket around the stem.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
An abutment is disposed between the implant and the crown and connects the implant and the crown.B · US 11,633,266 B2 · ¶ 3
The T studs 3 are welded at the base of the stud shank onto a metal surface 16, the stud head serving as a locking device for fastening elements.A · US 10,125,804 B2 · ¶ 19
The shaft portion 4b of the abutment 4 is inserted in an implant 3.B · US 11,633,266 B2 · ¶ 4
The T stud has a stud shank and a stud head with an underhead with a bearing face for bearing on at least one corresponding face which is formed on the retaining device.A · US 10,125,804 B2 · ¶ 2
An empty cell means only that no passage was reproduced there.
As a result, the fastening quality is reduced because the retaining element is not fastened in the correct position.A · US 10,125,804 B2 · ¶ 3
This measure makes it possible for the welding beads to enter into the recesses in the bearing shoulder, with the result that the bearing face of the underhead can come into contact on the corresponding face.A · US 10,125,804 B2 · ¶ 6
However, the shapes of the pre-milled blocks illustrated in FIG. 2 and FIG. 3 are merely examples, and the pre-milled blocks may be formed in various shapes.B · US 11,633,266 B2 · ¶ 4
In the first type of pre-milled block 300, a D cut surface 312 is formed as a rotation position reference in an outer peripheral surface 311 of the held portion 310.B · US 11,633,266 B2 · ¶ 6
patent.fyi, US 2026/0354943 A1, claim 1, first published 2026-11-19T06:07:06-05:00, https://patent.fyi/US20260354943/, SHA-256 eff15e45378287bddddf44ea21a004072c6a96e36938c9faed0ae97a9dfd4e23