1.1Single molded cup seal
A radial flange anchors the silicone cup in a groove in the handle bore. Fluid pressure acts on the open side of the cup and presses its inner lip against the delivery shaft.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A radial flange anchors the silicone cup in a groove in the handle bore. Fluid pressure acts on the open side of the cup and presses its inner lip against the delivery shaft.
An annular plate fastened to the handle face compresses the outer margins of two elastomer disks against a flat seat. The disks span the access port, and their central openings deflect around the delivery shaft.
A molded silicone plate seats in a matching pocket with a continuous compression ridge around its perimeter. The ridge seals the perimeter, and a central slit closes under elastic recovery after shaft withdrawal.
Two tapered silicone walls meet at a flattened outlet and spread as the delivery shaft passes between them. Elastic recovery brings the lips together after withdrawal, and pressure on the outside of the tapered walls reinforces closure.
A circular seal disk sits in a pocket whose center is offset from the shaft lumen. A guide bore directs the shaft to the offset cut pattern, where the cut regions flex and the elastomer grips the shaft.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A threaded seal housing mounts on a side port of a water treatment sampling manifold. The housing clamps a circular elastomer disk between an upstream shoulder and a threaded retainer, with partial-depth cuts near the center facing the probe entry. A tapered probe tip opens the cut region during insertion, and the elastomer grips the probe shaft while the probe measures conductivity in the flowing water.
A molded silicone septum with circular faces and a central through-bore replaces the disk with partial-depth cuts. The bore diameter is 85 percent of the mating shaft diameter, and a threaded cap clamps the septum rim against a housing shoulder. The bore expands around the shaft to form an interference seal, and an elastomer-faced screw plug closes the bore when the shaft is absent.
A 12 mm diameter, 2 mm thick silicone disk carries three 2 mm radial cuts that start at its center at angles of 0, 105, and 225 degrees. The cuts extend 1.0, 1.3, and 1.6 mm into the same face, respectively, leaving a continuous layer at the opposite face. An annular shoulder supports the disk rim, and the unequal cut depths give the three segments different bending resistance during passage of a tapered shaft.
A side port opens into the guide catheter lumen distal to the housing that retains the circular, partially cut seal. A three-way stopcock connects the side port to a fluid-filled pressure transducer line and a saline flush line. The stopcock selects the flush path during priming and the transducer path during monitoring, while the seal closes around the inserted delivery shaft.
A threaded compression cap and annular elastomer gland mount proximal to the housing pocket that holds the circular, partially cut seal. With the cap loosened, the shaft slides through the gland and the seal. Tightening the cap compresses the gland axially against a shoulder, causing it to contract radially around the shaft and hold its axial position.
A test fixture holds an assembled housing and connects the distal side of its partially cut seal to a regulated water supply. A motorized stage advances and retracts a rounded gauge shaft through the seal while a load cell records axial force and a balance under the proximal outlet measures collected water. The controller records peak insertion force and leakage rate at each test pressure and compares the measurements with stored acceptance limits.
Two silicone disks and a rigid annular spacer sit in a stepped bore. A threaded retaining ring bottoms against a shoulder to set the axial compression at the disk perimeters.
A compression molded silicone disk has two opposing flat circular faces and a cylindrical outer edge. An annular seat supports the distal face near its perimeter while leaving the central region free to deflect.
A depth stop limits two perpendicular blade passes through the center of the first face to 60 percent of the disk thickness. The remaining silicone forms a continuous web beneath the cuts.
Three straight cuts cross at the center of the first face at 60 degree intervals. Each cut reaches 70 percent of the disk thickness, leaving a continuous layer at the opposite face.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
It will be appreciated that portions of the seal stack assembly 101 may be disposed in each portion 107, 109 of the cavity 108 to form an annular seal between the housing 102 and the shaft 104.B · US 2022/0163118 A1 · ¶ 12
The sealing cuff 40c of FIG. 4C, as shown with sliding element 49c, is tulip shaped and has a circular cross-section.A · US 7,887,560 B2 · ¶ 65
Sealing cuff 200 has one or more slits 205 which divide sealing cuff 200 into portions 200a and 200b. A circular hole 205a may be provided to act as a stress reducer at the end of the slit.A · US 7,887,560 B2 · ¶ 84
An empty cell means only that no passage was reproduced there.
There is a risk of embolic material being released with any balloon expansion or passage of a treatment device through a diseased section of a vessel, with undesirable results to the patient.A · US 7,887,560 B2 · ¶ 4
The PTCA or Stenting treatment is then performed over the hollow wire and any embolic material is prevented from moving beyond the distal occlusion balloon.A · US 7,887,560 B2 · ¶ 6
These extreme operating conditions often necessitate the use of a seal stack assembly, which uses a plurality of individual seals, to provide an efficient and reliable seal along long probes or shafts that oscillate, reciprocate, rotate, vibrate, or combinations thereof with respect to a housing.B · US 2022/0163118 A1 · ¶ 2
At such extreme operating conditions, such as those present during the use of liquid hydrogen, traditional seal stack assemblies may not effectively maintain a seal.B · US 2022/0163118 A1 · ¶ 2
patent.fyi, US 2026/0354970 A1, claim 1, first published 2026-11-19T06:40:31-05:00, https://patent.fyi/US20260354970/, SHA-256 bf65831130713a4b5e5306663eea221dc12eb75b8a694f24f5bc2c98c02e2f3c