1.1Parallel shafts in separate lumens
A molded septum separates the two lumens of a common catheter jacket. One shaft carries the implant on a distal cradle, and the other drives a transverse yoke that withdraws the implant retainer.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A molded septum separates the two lumens of a common catheter jacket. One shaft carries the implant on a distal cradle, and the other drives a transverse yoke that withdraws the implant retainer.
Thrust collars capture the outer torque tube axially on the inner support shaft. Rotation aligns cutouts in a distal cam ring with spring fingers on the support shaft, allowing the fingers to open and free the implant tabs.
Retractable pins on the second shaft pass through eyelets on the implant frame. A pull wire withdraws the pins into guide bores, while a travel stop keeps the first shaft tip proximal to the retention assembly.
A continuous tube uses one polymer grade through the tip and first flex portion. A reduced wall thickness in the first flex portion lowers its bending stiffness, and the thicker tip wall supports contact with the implant retainer.
A stainless steel braid lies between the liner and the softer jacket in the second flex portion. The braid increases bending stiffness and supports the lumen during bending, while the unbraided first flex portion bends more readily.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An inner mandrel carries a collapsed spring mesh screen through curved process tubing. A sliding outer sleeve has a distal collar that contacts the screen rim, followed proximally by a softer first flex section, a harder second flex section and a bulk section harder than the second flex section. The sleeve holds the screen collapsed during insertion and retracts over the stationary mandrel to release the screen against the tube wall.
A machined acetal collar replaces the molded polymer tip of the translating outer shaft. The collar has a rounded contact face and a circumferential undercut that receives material from the softer first flex section during overmolding. The second flex section and bulk section follow proximally in order of increasing hardness. Translation of the outer shaft brings the collar face into contact with an implant shoulder supported on the inner shaft.
A 400 mm outer shaft for a benchtop valve fixture has a 2 mm distal tip, an 18 mm first flex section, a 12 mm second flex section and a 240 mm distal bulk section. A proximal section occupies the remaining 128 mm. The first flex section is softer than the tip and second flex section, and the bulk section is harder than the second flex section. The inner shaft holds a valve frame surrogate while a linear stage translates the outer shaft through a 20 mm stroke.
An outer shaft with a 4.0 mm bore uses a 0.30 mm wall in the first flex section and a 0.55 mm wall in the tip, second flex section and bulk section. External tapers extend 3 mm on each side of the thinner section and join it to the adjoining thicker walls. The first flex section uses a polymer softer than the tip and second flex section, and the bulk polymer is harder than the second flex polymer. The thinner section concentrates bending near the tip while the constant bore provides clearance for axial motion over the implant-supporting inner shaft.
A fiber optic force sensor mounts in an annular recess behind the distal tip collar on the translating outer shaft. Two annular shoulders transfer axial contact force from the collar through the sensor to the shaft body, proximal to which the two flex sections and the bulk section retain their hardness order. An optical fiber runs along the outer shaft to a proximal interrogator that converts wavelength shift to force using a calibration curve. The force display updates as the collar contacts an implant supported by the inner shaft.
A motorized lead screw drives a carriage attached to the outer shaft while a stationary clamp holds the implant-supporting inner shaft. The outer shaft retains the distal tip, the softer first flex section, the harder second flex section and the still harder bulk section. An encoder measures carriage travel and an inline load cell measures axial force between the carriage and the outer shaft. A controller stops the carriage at the programmed travel endpoint or when the measured force reaches a preset limit.
The first shaft uses a braided polymer tube with a fluoropolymer liner, and the second shaft runs concentrically through the lined bore. Diametral clearance permits axial sliding between the shafts.
An injection-molded polymer tip on the first shaft has a bevel leading into an annular recess. As the first shaft advances, the bevel guides retention tabs on the supported implant assembly into the recess.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
First portion 92 of provisional neck 90 includes cylindrical cavity 94 extending from surface 52 of proximal end 42 toward distal end 44. Additionally, distal end 58 of core 96 includes cylindrical projection 98 sized for receipt within cylindrical cavity 94 of first portion 92.A · US 2008/0133023 A1 · ¶ 38
Once inserted, the delivery catheter 110 can deliver the prosthetic heart valve 100 to the desired location within the anatomy and release the implantable heart valve 100 at a desired implantation site.B · US 10,314,696 B2 · ¶ 29
Additionally, the core of the provisional prosthetic component may have a scratch hardness greater than the scratch hardness of the first portion of the provisional prosthetic component and/or a stiffness sufficient to minimize deflection of the provisional prosthetic component during trial reduction and range of motion testing.A · US 2008/0133023 A1 · abstract
An empty cell means only that no passage was reproduced there.
In these systems, the provisional components should be designed to accommodate the forces encountered during trial reduction and range of motion testing without compromising the functionality of the mating junction of the final component.A · US 2008/0133023 A1 · ¶ 7
Advantageously, the design of the present provisional component allows for the use of a non-provisional modular prosthetic component during trialing of the provisional components.A · US 2008/0133023 A1 · ¶ 9
Accordingly, there is a desire to provide heart valves having sufficient long-term chemical stability, and physical and mechanical properties.B · US 10,314,696 B2 · ¶ 4
Prosthetic heart valves provided herein can have a structure adapted to retain functionality during the life of the patient with adequate chemical, physical and mechanical properties.B · US 10,314,696 B2 · ¶ 5
patent.fyi, US 2026/0354971 A1, claim 1, first published 2026-11-19T06:40:31-05:00, https://patent.fyi/US20260354971/, SHA-256 ffeeb9c6d2f2ecf8068210444c9cefca550d8acd999501768ae3eae2f2c94f8a