1.1Peripheral rim carries load
A continuous titanium rim surrounds a through-opening and bears against both end plates. The opening holds bone graft while the rim transmits compressive load between the vertebrae.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A continuous titanium rim surrounds a through-opening and bears against both end plates. The opening holds bone graft while the rim transmits compressive load between the vertebrae.
Solid titanium posts extend above and below a transverse frame and terminate in flat bearing faces. Each post transfers compressive load between the end plates, and the gaps between posts accommodate graft.
The upper crest concentrates contact along a line when the implant seats against the upper end plate. A broad rounded lower face distributes the same compressive force over a wider contact band.
The flat pad transfers compression through a broad contact face where it seats against the lower end plate. A narrow rounded crest on the upper side concentrates pressure against the upper end plate.
A flat titanium pad with a grit-blasted surface seats against the upper end plate. Axial compression presses the pad against the bone and generates friction that resists sliding.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A steel spacer sits between two timber coupons in a bolted lap joint. A rib runs along the spacer and presents a small crest radius to the upper coupon and a larger crest radius to the lower coupon. Bolt preload presses both crests into the wood, and the smaller crest concentrates pressure over a narrower region so it indents the upper coupon more deeply when both coupons have the same grain orientation and moisture content.
A solid titanium insert replaces the wall structure within an open cage frame. A dovetail at each longitudinal end of the insert engages a matching slot in the frame, and a transverse pin fixes the insert in position. The insert has a smaller transverse crest radius on its upper face and a larger radius on its lower face, with both crests projecting beyond the corresponding frame faces. Compression transfers through the solid insert and concentrates the initial upper contact over a narrower strip.
A family of compression specimens uses frame heights of 8, 10, and 12 mm and carries one straight internal wall in each frame. The upper and lower crest radii are 0.25 and 0.75 mm at 8 mm, 0.30 and 0.90 mm at 10 mm, and 0.35 and 1.05 mm at 12 mm. Each crest projects 0.40 mm beyond the adjacent frame face so that it contacts a flat test block before the frame does. The resulting three-to-one radius ratio preserves the orientation of the contact pressure bias across all three heights.
A straight internal wall has an upper crest radius of 0.30 mm and a lower crest radius of 0.90 mm. Flat bearing shoulders flank each crest and sit 0.25 mm below the upper crest apex and 0.45 mm below the lower crest apex, measured inward from the respective contact face. The crests engage first under compression, and each pair of shoulders engages once local indentation closes its gap. Shoulder engagement spreads the load over a wider area and reduces the incremental load carried by the crest.
An expandable interbody cage carries one longitudinal crest rail on its upper plate and one directly opposite on its lower plate. The upper rail has a smaller transverse crest radius, and both rails project above their respective plate faces by the same distance. A captive lead screw translates a wedge between the plates, and vertical guide slots maintain alignment as the wedge pushes the plates apart. The rails contact the opposing surfaces first, and the plate faces share the load once indentation closes the projection gap.
A motorized compression fixture holds the cage between matched synthetic bone blocks and tracks each block and the cage frame using optical displacement targets. A controller advances the platen at constant speed and records compressive force and relative approach at each interface throughout the loading ramp. Software subtracts calibrated elastic deflection from each interface measurement and fits indentation against time over the same force interval for both crests. The two fitted slopes quantify the indentation rate at each interface.
A machined titanium cage contains a longitudinal web formed integrally with its outer frame. The web presents superior and inferior bone-contacting portions and divides the graft cavity into two channels.
An additively manufactured titanium wall spans the graft cavity and joins two opposite sides of the implant frame. A solid core connects the superior and inferior edges, and open-cell porous titanium covers the bone-contacting portions.
A longitudinal web has a circular superior crest with a 0.25 mm radius and a circular inferior crest with a 1.25 mm radius. Both radii are measured in a transverse section perpendicular to the length of the web.
A titanium web has a narrow rounded superior crest and a broader rounded inferior crest. Under the same axial loading and comparable end plate conditions, the superior crest concentrates contact pressure over a narrower band and cuts into the upper end plate faster than the inferior crest cuts into the lower end plate.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The exemplary vertebral implant 10 includes a perimeter wall 12 that extends between a superior surface 14 and an inferior surface 16. The superior surface 14 and inferior surface 16 are bone-contact surfaces in that they are positioned adjacent to and facing a vertebral endplate once the vertebral implant 10 is inserted into a patient.A · US 2007/0270958 A1 · ¶ 19
First arm 52 and second arm 54 each define a portion of a top bone engaging surface 56 adapted to engage a vertebral body and a portion of bottom bone engaging surface 57 substantially identical to top bone engaging surface 56.B · US 2010/0161062 A1 · ¶ 47
Thus, the superior surface 14 is constructed with a smaller radius of curvature than the inferior surface 16.A · US 2007/0270958 A1 · ¶ 30
The bearing surfaces contact the adjacent vertebrae endplates to provide an even distribution of loads through the endplates and balanced loading conditions.B · US 2010/0161062 A1 · ¶ 70
An empty cell means only that no passage was reproduced there.
Therefore, certain conventional vertebral implants are not configured to take advantage of the natural anatomy of vertebral bodies so as to eliminate or reduce this bone preparation step.A · US 2007/0270958 A1 · ¶ 3
The superior and inferior surfaces may be disposed on a common body or on separate end plate members.A · US 2007/0270958 A1 · ¶ 4
Thus, there remains a need for implantable devices that have a reduced size insertion form and are expandable in the disc space to a larger size for enhancing spine stability and facilitating immobilization via bony fusion.B · US 2010/0161062 A1 · ¶ 5
Preferably, the height of the device in the reduced size configuration is substantially the same as the height in the expanded configuration, with the expanded configuration providing an increased base of support.B · US 2010/0161062 A1 · ¶ 6
patent.fyi, US 2026/0354984 A1, claim 1, first published 2026-11-19T06:40:31-05:00, https://patent.fyi/US20260354984/, SHA-256 00974e2c9ac3351a9f2a4230be291038d45c67f55889f59fd35129b65ad9ecbc