1.1Three bolted body sections
Two locating dowels register each side section against a machined face on the central section. Captive screws clamp the sections together, and the dowels carry transverse loads from the blade guides.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two locating dowels register each side section against a machined face on the central section. Captive screws clamp the sections together, and the dowels carry transverse loads from the blade guides.
Two contoured jaws grip the neck below the trunnion, and a transverse screw draws the jaws together. A replaceable stop bears against the prosthetic shoulder to set the guide height.
A bridge bolts to pads on the upper surface of the guide body and supports a split collet around the exposed segment of the trunnion. A draw screw closes the collet, and the bridge transfers blade loads between the guide body and the collet.
A keyed carriage slides on a linear rail and grips the proximal shank of a rigid blade. A spring-loaded pin locks the rail pivot at selected angles, and a travel stop limits blade advance.
Two pairs of opposed rollers support the broad faces of the blade at spaced points along its feed direction. A pin locks the roller carrier at a selected angle, and edge rollers constrain sideways movement as the blade advances.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A one-piece guide body fits over the exposed journal of an industrial conveyor roller. A split clamp seated in the central cavity grips the journal, and two groups of reciprocating saw slots flank the bearing collar. The slots guide the blade along opposite sides of the collar, and an adjustable stop on the saw shoe limits cut depth to leave a thin wall for a collar splitter to break.
A one-piece stainless steel body retains the central cavity and trunnion clamp. Pairs of ground zirconia inserts seated in open pockets on the medial and lateral portions form the blade guide slots. Captive cross pins hold the inserts against machined shoulders, and the opposing ground faces set the running clearance for each blade.
The one-piece body carries three parallel slots on each side of the central cavity, with slot centerlines at 8, 11, and 14 mm from the trunnion axis. Each slot is 1.10 mm wide and has a 10 mm guide length for a 1.00 mm thick rigid blade. With the central clamp seated on the trunnion, the operator selects the offset on each side independently to match the corresponding implant surface.
An integral external dovetail on the central portion accepts a removable carriage attached to a pneumatic orthopedic impactor. The carriage slides within the dovetail and locks at indexed positions that align the impactor with the medial or lateral blade slots. The impactor advances a rigid osteotome through the selected slot, and an adjustable stop collar on the blade shank limits its travel against the carriage face.
A compact optical scanner mounts to a locating face on the guide body, and a calibration fixture establishes the scanner position relative to the medial and lateral slot center planes. With the central clamp seated on the trunnion, software fits a surface to the scanned points on each exposed implant shoulder. For each side, the software displays the slot whose blade plane places the blade face closest to the measured shoulder without intersecting the implant.
A strain-gauged flexure between the clamp actuator and moving jaw measures compressive load inside the central cavity. A controller converts the flexure signal to clamping force using a calibration obtained with a reference load cell and illuminates an indicator when the force lies within a preset band. The controller stores the force at the start of blade use and signals a drop below the lower limit while the blade travels through either group of slots.
The central, medial, and lateral portions are machined from one stainless steel billet. A stepped cavity in the central portion provides a shoulder that sets the axial position of the securing assembly.
A segmented collet sits inside a tapered sleeve seated in the central cavity. A captive draw screw pulls the collet into the sleeve, which presses the segments against the trunnion.
Three medial slots have flared entries that ease blade insertion and straight bearing surfaces that set the blade path. Each straight section has a width equal to the specified blade thickness plus running clearance.
Three lateral slots are machined at 0, 5, and 10 degrees relative to the implant stem axis. Each slot has a radiused exit edge that supports a flexible blade as it bends toward the implant surface.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The vertical cut guide can have a body, a medial arm, and a lateral arm.A · US 2012/0316563 A1 · ¶ 4
The cut guide can have a body, a medial arm, and a lateral arm.B · US 10,485,555 B2 · abstract
With a reciprocating saw, a vertical medial cut 74 can be prepared while passing a saw through a medial slot 75a defined between a main body 75b of the vertical cut guide 72 and a medial arm 75c.A · US 2012/0316563 A1 · ¶ 61
With a reciprocating saw, a vertical medial cut 74 can be prepared while passing a saw through a medial slot 75a defined between a main body 75b of the vertical cut guide 72 and a medial arm 75c.B · US 10,485,555 B2 · ¶ 60
The vertical lateral cut 76 can be prepared while passing a saw through a lateral slot 77a defined between the main body 75b of the vertical cut guide 72 and a lateral arm 77c.A · US 2012/0316563 A1 · ¶ 61
The vertical lateral cut 76 can be prepared while passing a saw through a lateral slot 77a defined between the main body 75b of the vertical cut guide 72 and a lateral arm 77c.B · US 10,485,555 B2 · ¶ 60
An empty cell means only that no passage was reproduced there.
An instrument set for preparing a proximal tibia during a bi- cruciate retaining procedure can include a tibial resection block, a vertical cut guide, and a locking arm.A · US 2012/0316563 A1 · ¶ 4
A method for preparing a proximal tibia for receipt of a bi-cruciate implant can include determining a resection level of the proximal tibia.A · US 2012/0316563 A1 · ¶ 6
An instrument set for preparing a proximal tibia during a bi-cruciate retaining procedure can include a tibial resection block, a vertical cut guide, and a locking arm.B · US 10,485,555 B2 · ¶ 4
A method for preparing a proximal tibia for receipt of a bi-cruciate implant can include determining a resection level of the proximal tibia.B · US 10,485,555 B2 · ¶ 6
patent.fyi, US 2026/0354988 A1, claim 1, first published 2026-11-19T06:40:31-05:00, https://patent.fyi/US20260354988/, SHA-256 d3f6e06c65523b748fd9fec9ae46daa902aebc9926c620604cd938c4051b09ff