1.2Support behind the shell
A silicone support pad bonds directly to the chest-facing surface of the shell. A broad flange on the pad seats against the chest and spreads pressure from the bra band.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A silicone support pad bonds directly to the chest-facing surface of the shell. A broad flange on the pad seats against the chest and spreads pressure from the bra band.
A sealed elastomer envelope contains a homogeneous silicone gel. The gel shears under local pressure and redistributes load across the envelope.
Two sheets of thermoplastic elastomer seal at their perimeter to form a single bladder. A valve sets the fill pressure, which supports the front surface and allows it to yield under contact.
A pre-tensioned elastomer sheet clamps around the rim of a hollow breast-shaped shell. Inward shell movement stretches the sheet, and elastic recovery returns the shell to its resting position.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A breast-shaped silicone shell encloses a repeating polymer cell structure on an apparel fitting mannequin. A flat rear flange attaches the form to a rigid torso plate and transfers garment loads to the mannequin. Cell wall thickness sets bulk density and compressive compliance, and the wall material and void fraction set effective thermal conductivity. The form deforms under garment tension during fit checks.
Molded corrugated silicone sheets replace a printed core inside a breast-shaped silicone shell. Adjacent sheets alternate corrugation direction and bond at their contact points, forming repeated cell volumes through the stack. The trimmed stack bonds to the shell at its perimeter. Corrugation pitch and sheet thickness set bulk density and bending compliance, and silicone composition and air volume govern effective thermal conductivity.
Thermoformed thermoplastic polyurethane films replace the solid struts of a core with a stack of sealed air chambers inside a breast-shaped shell. Each layer consists of two formed films heat-welded along the perimeter of each chamber, and adjacent layers have offset chamber centers. The chamber walls flex and the enclosed air compresses under load. Chamber height and film gauge set bulk density and compliance, while the film-to-air ratio governs effective thermal conductivity.
A breast-shaped shell encloses a thermoplastic elastomer core with a cell pitch of 6 mm near the front and 3 mm near the rear. The pitch changes continuously across a 12 mm transition, and the nominal strut diameter stays at 0.8 mm. The finer rear cells place more solid material per unit volume near the mounting surface. The resulting geometry creates through-thickness differences in bulk density, compressive compliance, and effective thermal conductivity.
A breast-shaped shell with an internal polymer cell structure fits into a front-loading pocket in a support garment. A spacer-knit panel in the garment holds the rear face of the form away from the body and connects the resulting air channels to openings at the lower band and side seam. Garment motion exchanges air through the spacer layer, and the shell conducts heat between the core and the moving air. Core geometry sets bulk density and compressive compliance, while core material and void fraction govern effective thermal conductivity.
A flexible pressure sensor mat records contact pressure between a trial breast form and a support garment under a fixed strap tension. Software aligns the pressure map with a three-dimensional model of the form and assigns thinner cell walls to core regions behind high-pressure areas. A finite element model predicts the revised contact pressure, and the software iterates wall thickness while checking bulk density and effective thermal conductivity against target values. The final geometry exports as a printable core that fits inside the breast-shaped shell.
A flat silicone sheet fits in a fabric pocket against the chest. The molded foam cup holds its curved profile, and the bra band supports the weight of the sheet.
Spring ribs attach at both ends to a perimeter band, with taller arcs near the center of the cup. The bra fabric spans the gaps between ribs and presents a smooth contour under clothing.
A two-part mold forms a curved front and a shallow concave rear surface in silicone elastomer. The front sets the breast projection, and the rear follows the chest wall.
A heated mold shapes a closed-cell polyethylene foam blank into a rounded front with a tapered perimeter. A stretch-knit cover conforms to the foam and follows the taper under clothing.
A printed thermoplastic polyurethane lattice uses a repeating array of eight-millimeter cubic cells. Thinner struts near the chest-facing surface increase compliance, and thicker struts under the front surface support the contour.
A periodic gyroid sheet in silicone forms two continuous air passages inside the outer body. The sheet thickness and cell pitch set the solid fraction, which influences bulk density, compression stiffness, and effective thermal conductivity.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
All of the walls 32, 34, 36, 38 of the inner shell 30 are integral with one another in a one-piece molded plastic sheet and, due to their thinness and flexibility, generally conform to the generally hemispherical shape of the outer shell 40 and the generally U-shaped extension wall 48.A · US 2013/0338742 A1 · ¶ 22
The inner surface of an external breast prosthesis is the surface of the prosthesis that is designed for coinciding (adjoining.abutting) with an outer chest surface of a person wearing the breast prosthesis, notwithstanding that in between the chest surface and the inner surface of the prosthesis itself there is a liner, like a piece of cloth or otherwise. The inner surface of the prosthesis is opposed by an outer surface that provides the outer visible shape of the breast prosthesis.B · US 2023/0039216 A1 · ¶ 14
In a further embodiment of the method according to the invention the porosity of the reticulated solid foam, i.e. the volumetric void fraction in the solid foam, is between 50 and 95%, such as for example 50, 55, 60, 65, 70, 75, 70, 85, 90 or 95%. It was found that when using a TPE as polymer, at such a void fraction, adequate physical properties of the prosthesis for all various essential aspects (mechanical feel, heat transport, moist transport, density) can be provided in one and the same structure.B · US 2023/0039216 A1 · ¶ 22
An empty cell means only that no passage was reproduced there.
Yet, despite their beneficial therapeutic effects, it is often difficult to apply the cold compresses/heating packs to swollen/affected scrotal areas of differently sized individuals suffering from different levels of injury due to the different anatomical locations, shapes, and sizes of the swollen/affected scrotal areas.A · US 2013/0338742 A1 · ¶ 3
FIG. 1 is a perspective view of an apparatus for treating male genitalia with thermal therapy prior to adjustment to a treatment position in accordance with this invention.A · US 2013/0338742 A1 · ¶ 7
The method and prosthesis according to the invention allow an accommodation for an anomalous breast shape of a person due to surgery or other event inducing a shape differentiation, or a naturally existing shape differentiation.B · US 2023/0039216 A1 · ¶ 1
For example, it may become difficult to obtain satisfactory undergarments that will compensate for the deficit.B · US 2023/0039216 A1 · ¶ 2
patent.fyi, US 2026/0354989 A1, claim 1, first published 2026-11-19T06:40:31-05:00, https://patent.fyi/US20260354989/, SHA-256 6e6f0770f4efe35fe9ea4846a080741ff7d1a210a721caf52b49147ec47d31ea