1.1Direct electrode pickup
Two exposed platinum-iridium pads pick up the voltage difference at adjacent points on the muscle. Conductive traces carry the voltage to a differential amplifier, and a radio transmitter sends the digitized waveform.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two exposed platinum-iridium pads pick up the voltage difference at adjacent points on the muscle. Conductive traces carry the voltage to a differential amplifier, and a radio transmitter sends the digitized waveform.
Insulated leads carry the differential voltage from the passive pads to a sensing circuit sealed in a ceramic housing. The circuit amplifies and digitizes the waveform for radio transmission.
A platinum-iridium contact on the lead sits in adjacent tissue and connects to the amplifier reference input through an insulated conductor. The amplifier measures the pickup voltage relative to that contact before digitization.
An analog-to-digital converter at the sensor feeds a differential serial driver. An insulated twisted pair carries the sample frames to a receiver at the processor, which transmits the samples to the external unit by radio.
The processor receives the digitized EMG by radio and sends the sample frames over a differential electrical link. A sealed feedthrough carries the conductors across the skin to a detachable external cable.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A substrate sits between adjacent muscle surfaces in a canine hindlimb, with an EMG pickup in its upper face and reference contacts on its lower face. An implanted processor receives the sampled EMG by radio and forwards timestamped packets to a stationary receiver. A gait workstation aligns the EMG envelope with foot contact events from a pressure walkway and displays muscle activation by stride phase.
Two insulated capacitive plates replace the exposed sensing contacts in the upper face of the substrate, while a reference contact on the lower face remains in contact with muscle. Each plate feeds a high-input-impedance buffer, and the lower reference contact biases the inputs through high-value resistors. A differential amplifier subtracts the buffered signals, and a digitizer sends the samples by radio to the implanted processor for relay to the external receiver.
The upper-face sensor measures muscle voltage relative to the lower-face reference contact and applies an analog low-pass filter with a cutoff of 450 Hz. A 16-bit converter samples at 2,000 samples per second, and the transmitter groups 20 samples into each 10 ms packet with a sequence number. The implanted processor relays each packet to the external unit, which checks the sequence numbers and marks gaps in the reconstructed stream.
The upper-face EMG sensor and lower-face reference contact supply muscle activity samples to an implanted processor, which relays them to a powered hand controller. The hand controller maps the EMG envelope to a target grip force and reads fingertip load cells through its motor control board. After finger contact, a feedback loop adjusts motor current from the difference between target and measured grip force.
An upper-face EMG sensor measures muscle activity against the lower-face reference contact, and an implanted processor relays the samples to an external controller. The controller prompts the user through alternating rest periods and sustained contractions and computes the root mean square amplitude over 100 ms windows. It sets the baseline to the median of the rest windows and the upper calibration point to the 90th percentile of the contraction windows. It maps subsequent amplitudes between those points onto a proportional actuator command.
A programmable-gain amplifier connects the upper-face pickup and lower-face reference contact to the sensor digitizer. Sensor firmware counts samples near the converter limits over successive windows, lowers the gain when that count exceeds a threshold, and raises it after sustained low-amplitude recording. Each packet carries the gain setting used for its samples, and the implanted processor forwards that setting with the data. The external unit uses the gain setting to reconstruct input-referred amplitudes before computing the control signal.
Two metal pickup plates sit beneath a thin dielectric in the muscle-facing top surface. Local muscle potentials couple capacitively to the plates, and a high-input-impedance differential amplifier feeds a digitizer whose samples are transmitted by radio.
Two platinum discs sit flush with the bottom surface of a flexible silicone substrate and contact muscle. Embedded conductors tie the discs to the analog reference node through a bias network.
A planar coil at the substrate transmits digitized EMG by modulating a near-field carrier, and a second implanted coil feeds a demodulator connected to the processor. The processor sends the recovered samples through the skin using a radio link near 400 MHz.
The processor receives 16-bit EMG samples over a radio link at 2,000 samples per second per channel. It groups 20 samples per channel into numbered frames with an error-detection field and transmits them by radio to an external unit that reconstructs the waveform.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The fit of the gel liner 102 to the residual limb 101 can at least partially eliminate the loss of contact between the residual limb 101 and the electrodes 106 embedded within the gel liner 102, which makes myoelectric control of the prosthesis 124 more robust.A · US 2013/0046394 A1 · ¶ 28
As a result, the EMG signal data received from the electrodes 106 through the leads 108 can be transmitted to the socket interface 114 via the signal-conditioning electronics module 112. In one embodiment, the socket interface 114 can be coupled to the signal-conditioning electronics module 112; however, in some embodiments, the socket interface 114 and the signal-conditioning electronics module 112 can be in operative communication via a wired or a wireless connection.A · US 2013/0046394 A1 · ¶ 30
Beyond accumulating data from communicatively coupled components and sensors 115/165, the external electronics 120 may also share gathered data with other components of the TET system 100, such as with the clinical monitor 160 and implanted electronics 150. For example, the external electronics 120 may transmit all received and measured values to the clinical monitor 160 for further monitoring, logging, processing and/or analysis.B · US 10,376,624 B2 · ¶ 40
An empty cell means only that no passage was reproduced there.
This document generally relates to the field of powered prosthetic devices, and in particular to the embedding of conductive fabric electrodes and leads in a gel liner to allow detection of myoelectric signals for control of a prosthetic device.A · US 2013/0046394 A1 · ¶ 3
Myoelectric control eliminates much of the prominent and uncomfortable harnessing necessary for body-powered control and reduces the effort required by the wearer to actuate the limb; however, use of a myoelectric device requires physical contact between the electrode and the skin surface.A · US 2013/0046394 A1 · ¶ 5
Transcutaneous energy transfer (TET) systems are used to supply power to devices such as pumps implanted internally within a human body.B · US 10,376,624 B2 · ¶ 3
As such, there is a need for a system that assists the wearer in positioning or repositioning the transmitting coil.B · US 10,376,624 B2 · ¶ 6
patent.fyi, US 2026/0354991 A1, claim 1, first published 2026-11-19T06:40:31-05:00, https://patent.fyi/US20260354991/, SHA-256 d591c89484197153bb0f81678ca934290108f3a140ef125900d01b5e68e6d582