patent.fyi
Applications  /  US 2026/0354992
United States Patent Application Publication

US 2026/0354992 A1

Published
Nov 12, 2026
Filed
Apr 14, 2026
Earliest date on the face
Aug 30, 2019
Classification
A61F 2/76
First published here
Nov 19, 2026

Generated automatically. Not reviewed by a person. Not legal advice or an opinion.

Section 1 · machine-generated

What if?

Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.

No entries.

Section 2 · machine-generated

Variations

Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.

Other field of use

Touchdown sensing for warehouse robots

A warehouse robot leg carries an upper plate and a floating sole plate joined by four spring-loaded guide posts. Four Hall effect sensors on the upper plate face magnets on the sole plate at the toe, heel, and two sides. A corner-first touchdown compresses the springs unevenly, and the nearest sensor registers the largest decrease in gap. The leg controller signals contact when any gap decreases past its calibrated threshold and estimates the center of pressure from the four calibrated loads.

Component substitution

Inductive sensing with aluminum targets

Air-core printed coils replace the Hall effect sensors, and aluminum disks replace the magnets. The upper plate carries one coil opposite each disk on the spring-supported sole plate, with the coil and disk faces parallel at rest. An alternating current excites each coil in sequence, and eddy currents in the facing disk change the coil impedance as the gap closes. A calibration table converts measured impedance to gap and then converts gap to local load.

Parameter or scale variation

Six sensing points across a sole

A 240 mm sole carries six Hall effect sensor and magnet pairs in two rows of three, with stations 50 mm apart along the sole and rows 35 mm apart. Each pair mounts across a local compression spring that sets an unloaded air gap of 4 mm, and mechanical stops limit compression to 2 mm. The controller samples all six channels at 1 kHz and converts their readings to loads using a calibration for each station. It sums the station loads and computes the center of pressure from their load-weighted positions.

Combination with existing systems

Ground contact control for a hydraulic knee

A prosthetic foot carries heel and forefoot Hall effect sensors on its upper frame, with matching magnets on a compliant sole plate. A microcontroller converts changes in gap into heel and forefoot load estimates and reads a rotary encoder at the hydraulic knee. When heel load crosses a contact threshold, the controller commands an electronic valve to restrict hydraulic flow and increase knee flexion resistance. As both loads fall below an unloading threshold and the encoder registers flexion onset, the valve opens to allow swing flexion.

Automated or data-driven variant

Automatic zeroing during the swing phase

Three Hall effect sensors on an upper foot plate face three magnets on a compliant lower plate, and an inertial measurement unit mounts on the upper plate. The controller uses the inertial signal to identify mid-swing and checks that all three gap readings are stable and within stored unloaded ranges. During that interval, it updates each unloaded gap using a moving average of accepted samples. It holds the baselines fixed through stance and computes compression from each baseline and the corresponding measured gap.

Load estimation with a calibration matrix

Four distance sensors on a rigid upper plate face targets at the corners of a sole plate supported by an elastomer layer. A calibration fixture applies measured vertical forces at known positions while the controller records the four gap changes. Least-squares fitting produces a matrix that maps the gap changes to vertical force and moments about the fore-aft and lateral axes. During use, the controller applies the matrix to each set of readings and derives the center of pressure from the moments and force when the force exceeds a contact threshold.

Cite aspatent.fyi, US 2026/0354992 A1, claim 1, first published 2026-11-19T06:40:31-05:00, https://patent.fyi/US20260354992/, SHA-256 a749c6624dd6296f7e2adf11efc3cd9b15295d437c379fda08ecc7feddc1ea94
First published
Permanent addresshttps://patent.fyi/US20260354992/
Content fingerprint (SHA-256)a749c6624dd6296f7e2adf11efc3cd9b15295d437c379fda08ecc7feddc1ea94
Methodv2026-11-18.2 · automated, not reviewed by a person
Correctionscorrections@patent.fyi