1.1Separate skin contact liner
A smooth liner fits over the leg before the outer compression body is fitted. The outer body bears on the liner, which distributes the load across the skin and keeps the outer body physically separated from it.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A smooth liner fits over the leg before the outer compression body is fitted. The outer body bears on the liner, which distributes the load across the skin and keeps the outer body physically separated from it.
Overlapping woven panels wrap around the lower leg and close with circumferential straps. The wearer tensions each strap through a cam buckle to set the local circumference, and the buckles hold the panels under tension.
The wearer rolls the garment down to the heel pocket and inserts the foot. A thickened annular cuff provides a continuous gripping edge that the wearer advances up the leg during donning and rolls toward the foot during removal.
Each loop terminates in a woven anchor tape stitched into a structural seam allowance on the inside of the garment. The loop passes freely through a bound opening so hand tension transfers to the seam through the anchor tape.
Separate low-stretch tapes run from the calf loops through fabric channels to anchor patches at the heel, instep, and forefoot. The wearer tensions the loops in sequence to lift those portions during donning and uses the calf loops to grip the cuff when rolling the garment down for removal.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A circular-knit elastic sleeve covers the forearm from the wrist to below the elbow. Flat woven pulls are stitched to reinforced areas on the outer face at the wrist, mid-forearm, and upper opening. With the sleeve gathered at the wrist, the rower uses the wrist pull to seat the lower edge, then uses the middle and upper pulls to extend the sleeve toward the elbow. For removal, the rower folds the upper edge outward and uses the pulls in reverse order to roll the sleeve toward the hand.
Slotted silicone tabs replace the fabric loops on the outer face of an elastic sleeve. Each tab has a ribbed gripping end and a perforated base molded through an open-mesh textile anchor. The anchor extends beyond the base and is sewn to a reinforced area at each successive sleeve region. The wearer grips each tab in sequence to advance the sleeve and grips them in reverse sequence to roll it off.
A 240 mm elastic sleeve carries four pull stations centered 25, 85, 145, and 205 mm from its lower edge in the relaxed state. Each station has two 15 mm wide woven tabs mounted 180 degrees apart around the sleeve. The wearer pulls both tabs at a station together to distribute the axial load across opposite sides of the sleeve. The wearer progresses from the lower station to the upper station for donning and reverses the order for removal.
An elastic elbow sleeve fits beneath a hinged brace with rigid upper and lower cuffs. Sequential pulls sit on reinforced areas at the lower forearm, just below the elbow, and near the upper sleeve edge, along a line between the brace hinges. The wearer uses the pulls to position the sleeve, folds the tabs flat, and then closes the padded brace cuffs over the sleeve. For removal, the wearer opens the cuffs and uses the exposed pulls to roll the sleeve down the arm.
A depth camera captures the limb surface, and fitting software measures circumference at evenly spaced cross sections along the limb axis. The software uses circumference and axial position to locate the sleeve openings and intermediate regions where circumference changes fastest. It maps those positions to reinforcement marks on the flat pattern using the pattern's axial stretch allowance and adds a midpoint mark where adjacent pull positions exceed the specified spacing. During assembly, a pull is sewn to each marked reinforcement on the outer face for sequential use during donning and removal.
Each pull on the outer face of an elastic sleeve has a flexible strain sensor bonded to its textile anchor. Stretchable conductors connect the sensors and lights beside the pulls to a detachable controller at the sleeve opening. In donning mode, the controller lights the next pull in order after the active sensor registers tension above its calibrated threshold and then returns below it. A mode switch reverses the light sequence for removal.
A circular knit body incorporates covered elastomer yarn in circumferential courses. The relaxed circumference and elastomer feed tension vary along the leg to set the local compression on the intended fit range.
Low-stretch webbing loops sit on opposite sides of the outer face at each anatomical region. Bar tacks secure the loop ends through backing patches that spread hand loads across several knit courses.
Each pull uses a flat woven tab sewn at its center to the outer face, leaving a free end in each longitudinal direction. The wearer grips the upper end to draw the local fabric toward the calf and the lower end to turn the fabric toward the foot during removal.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The compression stocking is made of a woven or knit elastic fabric and is composed of different component materials, depending on the desired compression pressure.A · US 7,028,690 B2 · ¶ 26
The handles are essentially linear elongated cylinders that allow the user of the Aid to grasp the Aid and apply the necessary leverage to open the compression stocking for application.B · US 2017/0156531 A1 · ¶ 8
An empty cell means only that no passage was reproduced there.
This greatly restricts the patient's freedom of movement.A · US 7,028,690 B2 · ¶ 5
The object of this invention is to provide a compression support stocking with an improved effect.A · US 7,028,690 B2 · ¶ 7
Compression socks are notoriously difficult for a user to don.B · US 2017/0156531 A1 · ¶ 5
The handles are essentially linear elongated cylinders that allow the user of the Aid to grasp the Aid and apply the necessary leverage to open the compression stocking for application.B · US 2017/0156531 A1 · ¶ 8
patent.fyi, US 2026/0355019 A1, claim 1, first published 2026-11-19T07:16:45-05:00, https://patent.fyi/US20260355019/, SHA-256 ae719f42fa4a86713d7bdbf80196c814fe3714c01c920832219023fcd3c26d48