1.1Regulated supplied air
A supplied breathing-air line feeds a pressure regulator and a pressure-compensated flow valve. The valve meters air into an outlet manifold that feeds the breathing hose.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A supplied breathing-air line feeds a pressure regulator and a pressure-compensated flow valve. The valve meters air into an outlet manifold that feeds the breathing hose.
A motor and its controller sit on a separate mounting bracket outside the air-handling housing. A flexible shaft coupling transmits torque through a sealed bearing assembly to the impeller.
Bonded cell holders secure individual rechargeable cells inside the blower housing. Welded tabs and soldered leads connect the cells to a battery protection circuit that feeds the blower controller.
The pouch supports the battery independently of the blower housing. A two-conductor lead carries protected direct current from the battery to the blower controller.
The cradle converts mains power to high-frequency alternating current and drives a transmitter coil. A receiver coil inside the blower housing feeds a rectifier and voltage regulator that supply the blower controller with direct current.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A blower supplies filtered air through a flexible hose to a vented enclosure used for inspecting fragile textiles. A perforated panel at the hose outlet spreads airflow across the work surface. A latched battery module powers the blower during transport, and a separate cable inlet supplies mains power at the workbench.
Four brushless diaphragm pumps replace the motorized blower and connect in parallel between a filtered inlet manifold and a common discharge manifold. Flexible mounts isolate pump vibration, and a plenum downstream of the discharge manifold attenuates pressure pulsations. A motor controller drives the pumps from either the docked battery module or an isolated power supply fed through the mains cable inlet.
A centrifugal blower delivers 180 or 220 liters per minute through a 32 mm internal diameter outlet selected by a two-position switch. An outlet flow sensor feeds a controller that adjusts motor speed to hold the selected flow as filter resistance increases. A docked 24 V battery module and a 24 V supply fed through a separate mains inlet provide power to the same motor controller through isolated input paths.
A modular blower feeds the fresh-air inlet of a neonatal incubator through a sealed duct with a backflow damper. The incubator mixes the incoming filtered air with recirculated chamber air upstream of its heater and humidifier. The blower runs from a separate mains inlet at the care station and from its latched battery module during transfers.
Pressure taps upstream and downstream of the intake filter connect to a differential pressure sensor, and an outlet flow sensor measures delivered air. The controller compares the measured pressure drop with a clean-filter reference curve at the measured flow. It displays a filter service indication when the excess pressure drop stays above a stored threshold for 30 seconds. The controller receives power from either the latched battery module or the separate mains supply.
A mains inlet feeds an isolated DC supply, and a separate docking connector links the latched battery module to the blower. Reverse-current blocking switches connect both sources to a common motor supply rail. A voltage supervisor gives the mains supply priority and transfers the load to the battery when the mains-derived voltage falls below a set threshold. The supervisor returns the load to mains after the supply voltage remains above a higher threshold for two seconds.
A brushless direct-current motor drives a backward-curved impeller in a molded scroll housing. Air enters axially at the impeller eye and exits through a tangential outlet, while a Hall sensor feeds speed pulses to the motor controller.
Molded guide rails align the battery module as it slides onto the blower housing. A spring latch captures the module at the end of travel, where recessed spring contacts connect the battery output to the blower controller.
Two locating pins position the battery module against a flat face on the blower housing. An over-center cam latch draws the faces together and seats shrouded blade contacts in matching spring receptacles.
A recessed three-contact inlet accepts a detachable mains cord on the blower housing. The protective earth contact bonds to the metal chassis, and the line and neutral contacts feed an isolated alternating-current to direct-current supply connected to the blower controller.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
So mounting motor cover 14 both closes the cutout 16 and locates a blower 44 coaxial to the central axis A of circular cutout 16, within housing 12. The blower 44 pulls outside or re circulated inside air into housing 12 and blows it into the rest of HVAC case 10.A · US 7,118,355 B2 · ¶ 11
An apparatus, comprising: a chassis assembly including a housing and a midplane disposed within the housing; a power supply/blower assembly configured to connect to the midplane of the chassis assembly through a front of the housing in a field replaceable manner; a computing device configured to connect to the midplane of the chassis assembly through a back of the housing in a field replaceable manner; and a line cord supplying power to the power supply/blower assembly, the lB · US 7,969,747 B1 · claim 2
An empty cell means only that no passage was reproduced there.
A drawback of this structure, beyond the extra assembly step of folding over the flap C, is that the abutment of the duct to window E is one of hard plastic to hard plastic, with relatively little tolerance for molding or assembly irregularities at the direct interface.A · US 7,118,355 B2 · ¶ 3
The subject invention provides an alternative structure for providing an integral motor cooling air passage, with better sealing and higher tolerance at the joint.A · US 7,118,355 B2 · ¶ 4
These sources of EMI radiation challenge the equipment, designers, and engineers to find a solution to keep electronic signals coming to equipment clean and usable, isolated from the negative effects of the ever present EMI.B · US 7,969,747 B1 · ¶ 2
With respect to the conventional packaging of discoidal capacitor type filters, this means that in some applications it is desirable to have the capacitive element close to the threaded or screw-neck header end of the filter package, while in other cases the reverse is desirable, with the inductive element located on the threaded or screw-neck end.B · US 7,969,747 B1 · ¶ 7
patent.fyi, US 2026/0355034 A1, claim 1, first published 2026-11-19T07:16:45-05:00, https://patent.fyi/US20260355034/, SHA-256 a10ffda9603f5bffc23ab4522a720d6b4f4729f15c409b9a9a58a82346da52d8