1.1Textile wrist stabilization
Low-stretch straps cross the wrist and anchor to a padded forearm cuff and the hand wrap. Strap tension limits flexion and extension, while the cuff distributes the reaction load from finger actuation over the forearm.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Low-stretch straps cross the wrist and anchor to a padded forearm cuff and the hand wrap. Strap tension limits flexion and extension, while the cuff distributes the reaction load from finger actuation over the forearm.
A flexible cable housing carries a pull cable from a motor on the belt to a termination on the wrist cuff. The inner cable pulls the finger linkage, and the housing transfers the reaction load to the cuff.
A force sensor at each end of the pad registers pressure in one thumb direction. The controller issues the assigned command after the corresponding reading stays above a calibrated threshold for 100 milliseconds.
A two-position selector closes an enable contact when the user turns it to the run position. The controller enables the motor driver while the contact remains closed and disables it when the selector returns to the off position.
The motor turns a sector gear fixed to the linkage pivot near the base of the finger. A short connecting link transfers rotation to the next finger segment, and the controller limits travel using a rotary position sensor.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A worker wears the wrist support and finger assembly at a seated station for sorting lightweight parts. A wrist-mounted surface electromyography sensor feeds a controller that classifies grasp and release intent and commands the linear actuator to pull the corresponding finger mobilizers through their guides. A load cell at the actuator linkage measures pull force, and the controller stops increasing tension at the configured handling limit. The wrist display shows muscle activity and the active motion command.
A reversible geared motor replaces the linear actuator and mounts on the rigid wrist support. Two grooved drums on its output shaft wind the flexion and extension mobilizers in opposite directions, and spring-loaded idlers take up slack on the side that pays out. The controller reverses the motor to switch between opening and closing, and a shaft encoder provides position feedback for adjustable travel limits.
A linear actuator with a 20 mm stroke mounts on the rigid wrist support and drives the finger mobilizers through a common linkage. The controller limits travel to a calibrated segment of the stroke and selects a commanded speed of either 3 mm/s or 10 mm/s. Position feedback stops motion at either calibrated endpoint, and the wrist display shows the selected speed and current actuator position.
A grasp-training cylinder uses a split shell and an internal load cell to measure compressive grip force. The cylinder sends force readings over a short-range radio link to a tablet that also receives time-stamped muscle activity and actuator position from the wearable controller. During each prompted grasp-and-release cycle, the tablet plots grip force alongside muscle activity and records the peak force and release time.
Two surface electromyography channels on the forearm record muscle activity while the wrist display prompts rest, attempted closure, and attempted opening. The controller collects three labeled repetitions of each state with the actuator stationary and computes root-mean-square amplitude for each channel in 200 ms windows. It trains a linear classifier on those features and requires three consecutive matching classifications before issuing an opening or closing command. A rest classification stops actuator motion.
Bend sensors sewn into the back of the glove measure finger flexion, and an inline load cell measures tension in the actuator linkage. After the electromyography classifier identifies an opening or closing attempt, the controller compares measured finger motion with a calibrated position trajectory for that direction. It increases actuator pull when motion falls behind, reduces pull as the motion catches up, and stops at the calibrated endpoint or configured tension limit. The wrist display shows measured finger position and actuator tension.
A molded thermoplastic splint spans the back of the wrist and fastens to a stretch textile glove and a padded forearm cuff. Woven reinforcement at the finger attachments spreads actuation loads across the glove.
Two dry metal electrodes on the inner wrist measure a differential surface muscle signal relative to a reference electrode on the cuff. The microcontroller filters the signal, extracts amplitude features from 150-millisecond windows, and classifies each window as rest, opening, or closing.
A reversible motor turns a lead screw that translates a carriage connected to flexible finger mobilizers. The mobilizers slide in dorsal glove channels and transfer carriage motion to rings at the middle finger segments and capped rings at the fingertips.
A small monochrome display on the outer wrist shows a bar proportional to the filtered surface muscle signal amplitude. The controller refreshes the bar ten times per second and marks the calibrated resting level on the same scale.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
However, rather than directly associate the hamstring EMG with knee flexion and the quadriceps with knee extension, which would require the user to artificially isolate contraction of these muscle groups, the various embodiments incorporate a combination of pattern classification and principal component projection to align the measured EMG with the user's desire to flex or extend the knee joint.A · US 2017/0333222 A1 · ¶ 24
The visual biofeedback module 102 can be configured to receive video data, and corresponding video timestamp data, of a subject performing functional movements; and receive EMG data, and corresponding EMG timestamp data, from an electromyograph attached to the subject performing the functional movements.B · US 2019/0298205 A1 · ¶ 34
An empty cell means only that no passage was reproduced there.
An important class of movement, however, which does not involve any significant physical input from the user, is the task of non-weight-bearing or volitional control of knee movement while sitting or standing.A · US 2017/0333222 A1 · ¶ 6
Note that such volitional control is also useful in non-weight-bearing standing, such as when flexing the knee to look at the bottom of a shoe, or when placing the foot on an elevated surface (such as a chair) to tie or untie, or don or doff a shoe.A · US 2017/0333222 A1 · ¶ 6
This is because it can be difficult or impossible to determine from EMG data alone when the target muscle activated during the subject's functional movement, and whether the activation occurred before, for example, movement of a distal limb.B · US 2019/0298205 A1 · ¶ 7
It should be appreciated that there is a need for an improved EMG method that provides muscle activation patterns of target muscles during complex, functional movement, while providing insight on the timing of the muscle activation relative to the functional movement.B · US 2019/0298205 A1 · ¶ 8
patent.fyi, US 2026/0355040 A1, claim 1, first published 2026-11-19T07:16:45-05:00, https://patent.fyi/US20260355040/, SHA-256 f17b0e24369cf5c2aaa0b741b453a3ec41f9a064bdd76ace2ec29a9375388b26