Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
1.1Welded carrier with slip clutch
What ifWhat if the carrier stays welded to the exoskeleton and a joint clutch slips under overload?
Claim language“detachably connected with the exoskeleton system”
A welded aluminum bracket transfers cuff loads to the exoskeleton link. A spring-loaded friction clutch between the motor and the joint output slips above its set torque, allowing the link to rotate relative to the motor while the carrier stays attached.
1.1Trunk harness load transfer
What ifWhat if the attachment transfers assistive loads through the trunk without contacting the limbs?
Claim language“gripping the human limb”
A padded thoracic harness distributes the attachment load across the chest and upper back. A clevis on the rear harness plate connects to a powered back brace and pivots as the user bends forward.
1.1Strap through integral link slots
What ifWhat if the limb strap threads directly through slots in the exoskeleton link?
Claim language“on the carrier part”
A padded webbing strap passes through radiused slots formed in the structural link, which takes the strap tension directly. A pull-tab buckle in the webbing opens the loop for entry and removal.
Section 2 · machine-generated
Variations
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Other field of use
Forearm attachment for overhead assembly
A passive shoulder support for overhead assembly carries a forearm cradle on a detachable plate. A padded webbing strap wraps over the forearm and anchors to both sides of the cradle. A replaceable shear pin joins the plate to the support arm and fractures when a sudden transverse load exceeds its rated shear force, leaving the cradle and strap on the forearm.
Component substitution
Split elastomer sleeve for limb retention
A molded silicone sleeve serves as the holding member and bolts to the detachable carrier through a reinforced flange. A longitudinal slit lets the sleeve open around the limb, and two adjustable webbing bands close the slit. When a sudden load separates the carrier from the exoskeleton, the sleeve stays attached to the carrier.
Vacuum coupling for carrier release
A vacuum cup on the exoskeleton frame seats against a smooth face on the cuff carrier. A pump and check valve maintain vacuum, and a guide with a tapered exit carries lateral loads while allowing the carrier to lift clear. A load sensor on the frame opens a solenoid vent valve when the measured load crosses the release threshold. Air enters the cup and the applied load pulls the carrier away.
Parameter or scale variation
Carrier sizing for three forearm cuffs
Three padded cuff shells have internal widths of 55, 70, and 85 millimeters and share a carrier mounting pattern with two holes spaced 40 millimeters apart. Each shell bolts directly to the carrier and uses a 25-millimeter webbing strap to close around the forearm. A replaceable shear pin connects the carrier to the exoskeleton and releases under a sudden transverse load, so all three cuff sizes use the same frame interface.
Combination with existing systems
Release sensing for treadmill gait training
A gait training station combines a powered treadmill, an overhead body weight support harness, and an exoskeleton with a detachable lower leg cuff carrier. A proximity sensor on the exoskeleton frame detects a target on the carrier while the carrier is seated. When a sudden load separates the carrier, the sensor output changes state and the station controller commands a treadmill stop and disables drive torque at the affected joint. The overhead harness continues to support the user during the stop.
Automated or data-driven variant
Load rate sensing for carrier release
A strain gauge load cell sits between the exoskeleton frame and an electromagnet that holds the cuff carrier by a steel face. A controller samples the load at 1 kilohertz and calculates the load rise over a moving 10-millisecond window. When the measured force and its rate of rise both exceed configured thresholds, the controller switches off current to the magnet and the applied load separates the carrier. The controller stores the force samples and release time in an event log.
Specific version of a part
Release after sustained loading
A strain-gauge load cell in the carrier load path feeds a controller that starts a timer when the force crosses the threshold. The controller resets the timer when the force drops below the threshold and energizes a solenoid to retract the latch pin when the timer expires.
Flat adhesive skin interface
A flexible pad with a medical-grade pressure-sensitive adhesive bonds to a flat area of skin. A broad backing plate spreads low assistive loads across the pad in shear, and a rounded pull tab lets the user peel the pad away.
Spring-ball breakaway carrier
Spring-loaded balls in the exoskeleton socket seat in a circumferential groove on a carrier stud. During a sudden axial pull, the ramped groove drives the balls outward against their springs, freeing the stud when the pull exceeds the release force.
Magnetic carrier with locating bosses
Permanent magnets in the exoskeleton mount attract a steel plate on the carrier, and shallow locating bosses resist lateral movement. A sudden outward load separates the plate when the pull exceeds the magnetic holding force, and the bosses withdraw from their mating recesses.
Hinged calf gripping cuff
Two foam-lined polymer shells pivot on a hinge and partly encircle the calf. A ladder strap and ratchet buckle set the closing tension, and a bolted bracket secures the hinge-side shell to the carrier.
Cite aspatent.fyi, US 2026/0355041 A1, claim 1, first published 2026-11-19T07:16:45-05:00, https://patent.fyi/US20260355041/, SHA-256 97ed4137bf6de7e0178b8e6ff064324bc725bf7216dfa96aad17a39b615f0fcc