1.1Spring driven hip assistance
Hip extension winds a torsion spring through a cam. As the leg begins to swing forward, the spring unwinds and applies hip flexion torque through the cam.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Hip extension winds a torsion spring through a cam. As the leg begins to swing forward, the spring unwinds and applies hip flexion torque through the cam.
A motor winds a stranded steel cable onto a drum at the waist. The cable pulls on a thigh strap along a line offset from the hip joint, producing a hip flexion moment.
A lateral linkage runs from the waist to a footplate captured under the shoe insole. A hinge near the ankle allows ankle rotation while the linkage pushes on the footplate to assist forward leg swing.
Two conductive pads on the cuff liner contact bare skin, and a low amplitude alternating current passes between them. The processor measures the resulting voltage and compares the calculated impedance with a calibrated skin contact range.
A latch tongue closes a sealed microswitch when it reaches the locked position. The processor reads a digital input and accepts closure after the switch stays closed for 100 milliseconds.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A waist-mounted motor drives a lateral thigh frame on a wearable aid for a seated operator who repeatedly actuates a machine pedal. A padded thigh fastener couples the frame to the leg, and a pressure sensor measures contact between the fastener and thigh. When the contact pattern indicates seated fit, the controller enables hip flexion assistance during pedal release using a frame angle encoder to identify that phase.
A foil strain-gauge bridge on a stainless steel flexure replaces the pressure sensor at the thigh fastener. A floating pad of known area transfers the thigh contact load through the flexure to the fastener shell. The processor converts bridge voltage to calibrated force and divides by pad area to estimate mean contact pressure for the wearing decision.
A directionally opposed pair of sheathed cables replaces the rigid torque transmission frame between a waist-mounted motor and a thigh lever. The motor turns a two-groove drum that winds one cable while paying out the other, and the cables pull on opposite sides of a pivot aligned with the hip. A pressure sensor beneath the thigh fastener liner confirms contact before the controller enables the motor to apply torque through the lever.
Three 20 mm diameter pressure pads sit beneath the front and two sides of a 90 mm wide thigh fastener. The controller samples each pad at 100 Hz and computes its mean over the preceding 0.5 seconds. It enables active mode when the front pad and both side pads report sustained contact and each side pad contributes at least 15 percent of the summed mean pressure.
The wearable aid connects to a stationary rehabilitation cycle through an isolated wired link that carries crank angle and cadence from the cycle controller. The thigh fastener grips the leg above the knee, and its contact sensor supplies the wearing decision that enables active mode. In active mode, the wearable controller uses crank angle to time hip flexion assistance during the upward pedal stroke and sets its torque command to zero if crank data stops arriving.
A flexible pressure array sits beneath the thigh fastener liner and records the distribution of contact load. A classifier trained on labeled examples of centered fit, a twisted fastener, and partial seating uses contact area, center of pressure, and pressure distribution across the array. The controller enters active mode after the classifier reports centered fit in three consecutive sampling windows.
A brushless motor drives the hip output shaft through a toothed belt and a 4 to 1 pulley reduction. A motor current controller sets the drive current in proportion to the requested output torque.
A formed aluminum link bolts to the hip output flange and follows the outside of the thigh. The cuff mount slides along a slotted section of the link and clamps in place to fit different thigh lengths.
A curved polymer shell lined with closed-cell foam spreads the load across the thigh. A polyester strap wraps around the thigh, and a cam buckle holds the selected strap length.
A thin pad places a compressible dielectric between two flexible electrodes beneath the cuff liner. Thigh contact compresses the dielectric, and a capacitance converter uses a stored calibration curve to report pressure in kilopascals.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Still even further, the proximal thigh cuff circumferential support band consisting of an angled flexible thigh cuff permanently attached to the upper end of the uprights and an elastic strapping system attached to pivoting D rings on both upper ends of the uprights provides a dynamic band of support at the thigh, which conforms to the ever changing shape and angular dynamic motion of the leg during ambulation, running, and a myriad of other activities, all the while maintainA · US 8,308,671 B2 · ¶ 40
The straps are wrapped around the leg, free ends of the straps are attached to the articulating frame, and the tension of the straps are adjusted as desired.B · US 2023/0000657 A1 · ¶ 14
An empty cell means only that no passage was reproduced there.
Knee laxity, due to ligament injury, can cause significant instability to the knee joint thereby predisposing the joint to further instability and more serious injury.A · US 8,308,671 B2 · ¶ 4
Protecting and supporting a weakened knee joint after injury or pre or post-operatively, from the medial, lateral or rotational forces exerted upon the knee during walking, squatting and other movements is the primary purpose of a knee orthosis device for knee instability.A · US 8,308,671 B2 · ¶ 7
They typically employ a multitude of straps that require continuous lacing and unlacing each time, making it tedious to don and doff.B · US 2023/0000657 A1 · ¶ 3
This eliminates the need for threading the straps each time it is used.B · US 2023/0000657 A1 · ¶ 5
patent.fyi, US 2026/0355042 A1, claim 1, first published 2026-11-19T07:16:45-05:00, https://patent.fyi/US20260355042/, SHA-256 8a48257ac35873a1fdd317feaab2a0c757cfd5f73d77bf2640b190ae691de7c4