1.1Continuous cross frame panel
A single blank of coated woven fabric runs from one side frame to the other. Stitching at the two outer ends joins the blank to the side covers.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A single blank of coated woven fabric runs from one side frame to the other. Stitching at the two outer ends joins the blank to the side covers.
The left panel has a bound notch that clears the release lever throughout its travel. The right panel follows the full outline of its side frame, and the two sections join at the central seam.
The lower flap folds against the underside of the crossmember. The upper flap wraps over it, and a sewn-in elastic strip pulls the free edge inward against the overlap.
Flexible C-shaped clips attached to each panel snap around the adjacent tubes. Each panel covers one face of the side frame, and its edges remain separate from the other panel.
Stitched end seams close the top and bottom of a receptacle sized to enclose the side frame. A zipper along the outer face opens for lateral insertion and closes after the frame sits inside.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A washable cover fits the four upright posts, two side rails, and front crossbar of a plant transport cart. Two mirror-image panels meet at a central seam over the crossbar, where upper and lower flaps wrap around the bar. Each side panel has inner and outer flaps that form a rail pocket with a top aperture for a push-handle stem and a bottom opening that feeds into two post wraps. Each post wrap closes above the caster swivel with a mating fastener pair marked with a distinct matching symbol.
Separating coil zippers replace the paired flap fasteners on the crossmember and legs. On each crossmember section, one zipper tape is sewn to the upper flap edge and the mating tape to the lower flap edge. On each leg, the tapes are sewn to opposite edges of the same wrap, with the insertion pin and box at the lower end and the closed slider at the upper end. Matching thread colors identify the two tapes of each closure, and a fabric strip behind each zipper sits between the coil and the frame tube.
Two sliding crossmember sleeves fit straight spans from 380 to 500 mm, with at least 60 mm of sleeve overlap at maximum extension. Each sleeve retains upper and lower wrap flaps, and a central webbing strap with a cam buckle locks the overlap after adjustment. Each of the four leg wraps fits tubes from 22 to 32 mm in outside diameter using a 75 mm fastening strip and a 25 mm mating tab. The installer centers the overlapping sleeves, sets the span, and tightens each leg wrap independently.
A two-panel cover fits a folding walking frame with pivoting side frames and spring-loaded release levers at the front joints. The crossmember flaps wrap the fixed span between the joints, and each side pocket moves with its own side frame. A bound cutout exposes each release lever through its full travel, and a fabric pleat between the crossmember sleeve and each side pocket collapses as the joint closes. The leg wraps end above the height-adjustment buttons so those buttons remain reachable while the cover is installed.
A fixed camera captures front and side views of the frame with a scale marker in each view. Software traces the visible tube edges, converts pixel distances to millimeters, and combines the two views to locate the crossmember ends, handle stems, and four leg axes. A pattern generator uses the measured crossmember span, side rail lengths, and tube diameters to lay out the two cover halves, leg wraps, and handle apertures with specified seam allowances. It exports cutting paths with registration marks for the central seam and a distinct pair of matching marks for each closure.
Each crossmember and leg wrap carries a sealed, spring-return plunger switch on one flap and a rigid actuator tab on its mating flap. A small bracket holds each switch beside its fastener so the seated mating flap depresses the plunger. Flexible wiring follows the seams to a battery-powered controller in a detachable crossmember pouch. When the user presses a check button, the controller reads each switch and illuminates the indicator labeled for each open closure.
Two mirror-image sections are cut from coated woven polyester, each with a cross frame cover and a side frame cover. The inner ends of the cross frame covers overlap by 12 mm and are joined with two rows of lockstitch along the centerline.
An acetal snap socket mounts on the underside of the upper flap, and its mating stud mounts on the outward face of the lower flap. The stud and socket use a profile that mates only with the cross frame pair.
A coated polyester outer flap and a woven nylon inner flap are stitched together along the side edges to form the receptacle. Folded polyester binding reinforces the top aperture and bottom opening.
A stud mounts on one wrap portion of each leg, and its mating socket mounts on the other portion of the same leg. Each pair uses a distinct key and slot profile that prevents engagement with the other leg pairs and the cross frame pair.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A right leg 5 having an upper edge 7, a front section 8 and a rear section 9 is attached to a left leg 6 having an upper edge 7, a front section 8 and a rear section 9 along a center seam 10 via an fastening means 11, such as a zipper 12 (as shown here), a hook and loop fastener, snaps, etc.B · US 2011/0167537 A1 · ¶ 33
The cover 23 can be secured to the housing by any suitable means, such as screws or a snap-tab closure.A · US 2008/0072941 A1 · ¶ 20
An empty cell means only that no passage was reproduced there.
Currently, ambulatory aids do not enable physicians, physical therapists, and caregivers to monitor the number of steps taken by a user of the ambulatory aid.A · US 2008/0072941 A1 · ¶ 3
The ability to monitor the number of steps taken by a user of an ambulatory aid is desirable, however, inasmuch as it would enable one to monitor overall activity level and recovery progress.A · US 2008/0072941 A1 · ¶ 3
Therefore, a need exists for a pair of pants having an invisible opening that will allow a person to go to the bathroom without having to lower the pants and/or remove any gear from the pants.B · US 2011/0167537 A1 · ¶ 3
The primary object of the present invention is to provide a pair of pants that allow a wearer to use the bathroom without having to remove the pants.B · US 2011/0167537 A1 · ¶ 5
patent.fyi, US 2026/0355043 A1, claim 1, first published 2026-11-19T07:16:45-05:00, https://patent.fyi/US20260355043/, SHA-256 6b39cc2e7eaaae6d5a809e5c005875fbb0e2c3342e3354599d1ca8be1708efb3