1.1Vents through shell walls
Molded slots in opposite ends of the outer shell serve as the inlet and outlet. A gasket seals the shell joint, and a blower draws air through the inlet, across the heat sink, and out through the outlet.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Molded slots in opposite ends of the outer shell serve as the inlet and outlet. A gasket seals the shell joint, and a blower draws air through the inlet, across the heat sink, and out through the outlet.
A single injection-molded shell has integral bosses that support the blower and heat sink. A silicone pad fits over the face-side rim, and a retained compress plate projects through a central opening in the pad.
A copper spreader conducts waste heat from the thermoelectric module to a sealed aluminum backplate. Integral fins on the backplate release heat to ambient air by natural convection.
A flexible sealed pouch filled with water-based gel slides into a pocket behind a thin fabric liner. The user warms the pouch in a water bath for a hot compress or chills it in a refrigerator for a cold compress.
A direct-current driver powers the thermoelectric module with one polarity during cooling. During heating, the controller switches off the module and powers an etched-foil heater bonded to the compress plate.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A benchtop fixture presses a flat aluminum contact plate against the backing of an adhesive test coupon. A reversible thermoelectric module mounts between the plate and a finned heat exchanger inside a two-piece housing. Air enters through a gap between the housing pieces and exits through slots in the outer shell. A polarity switch selects heating or cooling while a thermocouple records the coupon temperature.
A flat copper vapor chamber replaces the solid base of the finned heat exchanger behind the thermoelectric module. The chamber contacts the module face opposite the compress plate and extends to a fin stack near the outlet. During cooling, working fluid evaporates above the module, condenses beneath the fins, and returns through an internal wick. Air enters through the gap between the housing pieces, crosses the fins, and leaves through the outlet.
A pumped liquid loop replaces the heat sink mounted directly against the thermoelectric module. A sealed cold plate contacts the module face opposite the compress plate, and flexible tubing connects it to a miniature pump and a finned radiator in the outer shell. The pump circulates water-glycol coolant between the cold plate and radiator. A fan moves air from the housing-gap inlet through the radiator and out through a separate outlet.
Two 25 mm by 35 mm compress plates sit on 64 mm centers, each coupled to a separate 20 mm by 20 mm thermoelectric module. Each module has a separate heat sink and a reversible current driver with a 1.5 A current limit. A center partition divides air from a 2 mm housing-gap inlet into two paths, each leading across one heat sink to a separate outlet. The two drivers select heating or cooling independently.
Two low-profile air bladders mount beside the compress plates along the brow and cheek contact zones. A miniature diaphragm pump fills the bladders through separate inlet valves, and exhaust valves release air between pressure cycles. The thermoelectric modules and their heat exchangers sit behind the plates in a ventilated housing compartment. A sealed partition separates the bladder tubing from the airflow path between the housing-gap inlet and the outlet.
A thermistor sits in a shallow blind bore behind the contact surface, and a second thermistor mounts at the heat sink base. A microcontroller samples both sensors at 10 Hz and adjusts a bidirectional current driver to hold a selected plate temperature. The controller ramps current to zero before reversing polarity. It disables thermoelectric drive when the heat sink exceeds its configured temperature limit or either sensor reports an open or short circuit.
Molded ribs maintain a 2 mm gap along the lower seam between the outer and inner housings. A centrifugal blower draws air through the seam gap and discharges it through slots in the upper wall of the outer housing.
The outer housing overlaps the inner housing at the left and right edges, leaving a gap at each edge. A foam baffle separates the left inlet from the right outlet and directs blower airflow across the heat sink.
A four-transistor bridge reverses current through a ceramic-faced thermoelectric module. A thin layer of thermal grease couples the face-side working surface to an anodized aluminum compress plate, and a thermistor bonded to the plate provides feedback for temperature control.
A copper base clamps against the rear working surface of the thermoelectric module and spreads heat into bonded aluminum fins. A centrifugal blower inside the housing drives air through the fin channels, and a molded duct carries the warmed air to the outlet.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A front end of the mask frame 36 is a mask body 32 made of soft material. The mask body 32 is formed with two through holes 31 at positions corresponding to those of eyes of users.A · US 2005/0137445 A1 · ¶ 18
It is important to note that this phenomenon may be reversed whereby a change in the polarity (plus and minus) of the applied DC voltage will cause heat to be moved in the opposite direction. Consequently, a thermoelectric module may be used for both heating and cooling thereby making it highly suitable for precise temperature control applications.B · US 8,497,515 B1 · ¶ 11
An empty cell means only that no passage was reproduced there.
However the defect of the prior art eye massager is that the user must holds the massage bar to touch and press the periphery of the eyes.A · US 2005/0137445 A1 · ¶ 3
Accordingly, the primary object of the present invention is to provide an eye massager which can be used easily and conveniently.A · US 2005/0137445 A1 · ¶ 4
LED lighting devices generate critical thermal energy which, if not removed, may prevent proper functioning of the device or limit the lifetime of the device.B · US 8,497,515 B1 · ¶ 6
FIG. 1 illustrates an exemplary LED lighting device employing a heat sink/housing in thermal communication with the LED element so as to provide cooling by dissipating heat into the ambient air.B · US 8,497,515 B1 · ¶ 6
patent.fyi, US 2026/0355046 A1, claim 1, first published 2026-11-19T07:16:45-05:00, https://patent.fyi/US20260355046/, SHA-256 563f5fc887aedcefa3860ee28e50f547b1c92c7203893cff3432caf3a7baf0cb