1.1Traveling roller pressure
A geared motor pulls a roller carriage along parallel rails at a steady speed. Compression springs press the roller against a flexible contact sheet, which transfers the moving load to the body.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A geared motor pulls a roller carriage along parallel rails at a steady speed. Compression springs press the roller against a flexible contact sheet, which transfers the moving load to the body.
An eccentric motor bolts to a rigid insert molded into the center of a silicone contact pad. The insert transfers the motor's oscillating force into the pad on both sides of the midpoint.
A molded silicone sheet has a thin central web and thicker edges. The web bends under strap tension, and the reinforced edges transmit vibration from the drive into the contact surface.
Molded tabs at the midpoint of each long side receive the two ends of an adjustable textile strap. The strap wraps around the limb and pulls the pad against the skin through the side tabs.
A spring-counterbalanced arm on a floor stand supports the vibrating head on a pivot. A compression spring applies contact force, and a smooth face lets the head slide as the operator guides the arm.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A flexible silicone band with an oblong opening through its thickness wraps against the dancer's forearm. An eccentric rotating mass motor mounts at one end of the band, and a hook-and-loop strap attached to the opposite end closes around the forearm. A battery-powered timer pulses the motor at the rehearsal tempo and lengthens every fourth pulse to mark the start of a measure.
A moving coil actuator replaces the rotary motor at one end of a flexible band with a through-opening. The actuator housing fastens to the end of the band and guides a spring-mounted moving mass along an axis normal to the local contact surface. A belt attached to the opposite end bends the band against the body, and an alternating current in the coil oscillates the mass and transfers vibration through the housing into the band.
A ratcheting cable dial replaces a buckle closure at the end opposite the actuator on a flexible band with a through-opening. The dial anchors to that end and reels in a braided cable routed around the body through guides on a padded backing strip, with the cable terminating at a tab beside the actuator housing. Turning the dial shortens the cable loop and bends the band into contact with the body, while releasing the ratchet lets the cable extend for removal.
A 140 mm by 45 mm elastomer band is 3 mm thick and contains a centered 80 mm by 18 mm oblong opening through its thickness. A motor housing clamps onto one solid end, and an adjustable strap attaches through a slot in the opposite solid end. The strap bends the band against the calf, and a timer switches an eccentric rotating mass motor on for 2 seconds and off for 3 seconds in a repeating cycle.
A flexible perforated band sits inside the upper cuff of a hinged knee brace, with its contact surface facing the thigh. The actuator housing clips to one side of the cuff, and the opposite end of the band attaches to the cuff closure strap. Tightening the cuff draws the band against the thigh, and a switch on the outer cuff powers the actuator through a cable routed along the cuff seam.
A flexible band with a through-opening carries an eccentric rotating mass motor at one end and an adjustable retention strap at the other. A small accelerometer mounts on a solid section beside the opening, with one sensing axis normal to the contact surface. A controller filters that axis around the motor's operating frequency and adjusts the motor duty cycle to hold the measured root-mean-square acceleration at a setpoint as strap tension changes.
A direct-current motor with an eccentric shaft weight bolts to a rigid insert molded into the first end of the massaging assembly. At 6,000 revolutions per minute, the rotating weight applies a 100 hertz oscillating force to the insert.
An elongated slot with rounded ends passes through a 3 millimeter silicone pad from the outer face to the skin-facing face. The two side ligaments bend under strap tension and carry vibration along the pad.
A 25 millimeter woven polyester strap loops through a molded eye at the second end of the massaging assembly. A sliding buckle adjusts the loop circumference and holds the selected tension around the limb.
A soft silicone contact face has a thin web that bends around the limb as the strap tightens. Skin contact pressure flattens shallow molded ribs, increasing the contact area and limiting slip during vibration.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Preferably, the attachment means 16 is a round hole through the contoured massage head 10, made substantially perpendicular to the bottom surface 12. An attachment knob 20 having a knob head 21 and a threaded rod 22 secures the contoured massage head 10 to the massage appliance 30.A · US 2008/0071203 A1 · ¶ 23
Such devices as a vibration motor to realize the vibration may also be provided on the sphincter massaging head.B · US 2019/0282438 A1 · ¶ 106
The present disclosure relates to a body massaging device and an operation method thereof, wherein, the body massaging device comprises a support holder detachably mounted on a lower limb of a body; and an anal massaging assembly mounted on the support holder for compressing and/or rubbing an anus of the body as well as perianal skin.B · US 2019/0282438 A1 · abstract
An empty cell means only that no passage was reproduced there.
This invention relates to therapeutic massage tools, specifically to a contoured blade head for attachment to a percussive mechanical massage tool specially shaped to the contours of affected regions of a patient's body.A · US 2008/0071203 A1 · ¶ 2
However, soft tissue therapy with a hand tool still requires a significant exertion of force and suffers the same problem of a manual massage, that of inconsistent pressure inherent in any manual manipulation of the soft tissues.A · US 2008/0071203 A1 · ¶ 6
In view of this, the present disclosure proposes a body massaging device and an operation method thereof, which are capable of providing a stimulation effect different from the existing massaging appliances, and making a user less prone to fatigue during the use.B · US 2019/0282438 A1 · ¶ 5
In some embodiments, the support holder includes: a leg clamping structure, for clamping and fixing a leg of the body; and a massaging assembly mounting bracket, mounted on the leg clamping structure, for mounting various massaging assemblies.B · US 2019/0282438 A1 · ¶ 7
patent.fyi, US 2026/0355053 A1, claim 1, first published 2026-11-19T07:16:45-05:00, https://patent.fyi/US20260355053/, SHA-256 3adfa3a113f948fb3f319f2bd47351bc63ef55bb96f52bb50dfc25b02e92cbfc