1.1Rollers compress the tubing
A motor turns a rotor carrying three rollers that advance successive occlusions along the tubing to move fluid. An air detector monitors the outlet tubing downstream of the track.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A motor turns a rotor carrying three rollers that advance successive occlusions along the tubing to move fluid. An air detector monitors the outlet tubing downstream of the track.
Each clamp captures a rigid collar bonded around the tubing outside the compression zone. The flat backer face carries the transverse load, and the collars resist lengthwise movement without squeezing the fluid passage.
A transmitting piezoelectric element sends bursts through the outlet tubing to a receiving element in the opposite jaw. The detector flags an air interval when the received amplitude falls below a calibrated threshold for consecutive bursts.
An infrared emitter directs light obliquely into a transparent tubing segment beside the plunger. A photodiode measures the change in light refracted by the tubing and its contents as air passes through the sensing zone.
A motor drives a lead screw that moves the plunger in both directions. During engagement, a controller uses load cell feedback to regulate compressive force and then reverses the motor to retract the plunger.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A beverage concentrate pump seats its flexible outlet tube in a backer channel bounded by a front wedge and a rear barrier. A spring urges a retractable plunger against the tube, and ultrasonic modules housed in the plunger and backer measure transmission across the tube. The controller pauses dispensing when transmission drops below the threshold for a liquid-filled tube and resumes after priming restores the liquid signal.
A pair of parallel stainless steel leaf springs replaces the separate compression spring and sliding plunger guide. Each leaf spring attaches at one end to the pump frame and at the other end to the plunger carrier, with the springs preloaded toward the backer. A pull solenoid retracts the carrier for tube loading, and releasing the solenoid returns the plunger to the tube for measurement between the two embedded sensing modules.
Copper electrodes replace the acoustic sensing elements and sit behind insulating faces in the plunger and backer. The spring-loaded plunger presses the tube into the backer channel and sets the electrode spacing against a mechanical stop. A capacitance measurement circuit drives one electrode with an alternating voltage and measures the coupled signal at the other. The controller classifies the tube contents using a threshold between readings from air-filled and liquid-filled sections of the installed tube.
Two independent spring-loaded plungers face a common backer channel at stations 20 mm apart along a tube with a 3 mm inner diameter. Each plunger faces a separate sensing module in the backer, and the controller samples both stations at 1 kHz. The controller matches the leading air transitions at the two stations and divides the station spacing by their transit time to estimate bubble speed. It multiplies that speed by the air interval at the downstream station to estimate bubble length.
A pump outlet passes through the backer channel and between the embedded sensing modules before reaching a three-port priming valve. The valve connects the outlet to either a delivery line or a collection reservoir, and a spring-loaded plunger holds sensor contact during both valve states. When the detector reports air, the controller stops the pump, switches the valve to the reservoir, and restarts the pump at its priming rate. After the detector reports continuous liquid and the pump displaces the volume between the detector and valve, the controller stops the pump, switches the valve to the delivery line, and resumes delivery.
A shaft encoder measures increments of pump motion while opposed sensing modules in the spring-loaded plunger and backer sample the fluid path. During liquid-filled calibration, the controller stores the delivered volume per encoder increment for each forward-flow phase of the pump cycle. During operation, it adds the calibrated volume of each forward-flow increment to an air-volume counter when the detector reports air at that increment. The controller retains the accumulated volume across separate air events until a reset command clears the counter.
A stainless steel plunger slides in two polymer bushings along an axis perpendicular to the tubing. Its broad shoe has rounded edges that distribute contact across the flexible tube wall during engagement.
An injection molded backer has a sloped front wedge and an upright rear rib that run along the tubing segment. The wedge guides the tube into the channel, and the rear rib limits lateral movement during compression.
A piezoelectric receiving element sits in a recess inside the plunger behind an elastomer acoustic window at the contact face. An opposed transmitter sends bursts through the tubing, and a receiver circuit measures the transmitted amplitude while the plunger is engaged.
A stainless steel coil spring sits between a fixed frame seat and a shoulder on the plunger. The spring remains compressed throughout the stroke and applies force toward the tubing during engagement.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The second member 34 is bi-directionally movable in bore 38 as indicated at D to retract and extend between a raised position R and a lowered position L due to compression of resilient member 36.A · US 6,995,982 B2 · ¶ 17
The curtain rod retaining section 1100 includes a partially open interior channel 1110 with the interior surface 1064 of a semi-circular wall 1060 and spaced apart interior surface 1054 of first transverse wall 1050 and interior surface 1074 of second transverse wall 1070 with an opening 1112 between the first curved portion 1038 and the interior surface 1084 of the upper arcuate top wall 1380 extending to the bottom semi-circular wall 1060, an elongated portion of a curtainB · US 10,123,647 B1 · ¶ 48
The spring keeps the plunger biased down as it rides over an anchor in the sheet metal and drops into the retaining hole.A · US 6,995,982 B2 · ¶ 24
An empty cell means only that no passage was reproduced there.
Therefore, what is needed is a tool-less device for installing and removing a circuit board, which improves upon the previously used devices.A · US 6,995,982 B2 · ¶ 5
A principal advantage of this embodiment is that a tool-less method for installing and removing a circuit board is provided which does not damage the circuit traces.A · US 6,995,982 B2 · ¶ 7
The device disclosed in this patent does not have a mechanism to tighten the device to the window blind bracket, which does not have any feature to accommodate different depths of a window blind brackets and any mechanism to prevent movement of the curtain rod.B · US 10,123,647 B1 · ¶ 12
The device disclosed in this patent does not have a mechanism to tighten the device to the window blind bracket, which does not have any feature to accommodate different depths of a window blind brackets and any mechanism to prevent movement of the curtain rod.B · US 10,123,647 B1 · ¶ 16
patent.fyi, US 2026/0355427 A1, claim 1, first published 2026-11-19T11:28:41-05:00, https://patent.fyi/US20260355427/, SHA-256 d56d8749789eb7c3198ddcd25387f6891f8db795f2ebce30bfd1b7f900c1824d