1.1Oblique housing split
The first housing section seats in a chassis cradle, and the second section closes against its inclined perimeter flange. Screws oriented normal to the flange compress a continuous gasket around the joint.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The first housing section seats in a chassis cradle, and the second section closes against its inclined perimeter flange. Screws oriented normal to the flange compress a continuous gasket around the joint.
A flush microperforated liner backed by sealed shallow cavities follows the walls of an undivided intake passage. Acoustic oscillations drive air through the perforations and dissipate energy through viscous losses as the main airflow continues to the fan chamber.
Four elastomer bobbins carry the load between mounting feet on the fan casing and bosses on the chamber floor. A flexible outlet coupling accommodates motion of the fan and limits vibration transfer to the delivery duct.
A sealed side cavity connects through a short neck to the duct wall at the height of the fan inlet. The neck area, effective neck length, and cavity volume set the resonant frequency near the dominant inlet tone.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A suction blower draws air through a perforated document transport belt to hold sheets flat during scanning. The blower intake connects to a two-piece sealed enclosure downstream of the belt plenum and a removable dust filter. Internal ribs divide the intake passage into communicating chambers, and an elastomer sleeve suspends the blower in the final compartment. A perforated panel over a closed air cavity sits beneath the blower inlet and attenuates intake noise.
Four elastomer bobbin mounts replace the fan sleeve and connect the blower frame to bosses inside the fan chamber. Each mount has separate threaded inserts bonded to opposite ends of its elastomer body, which interrupts the rigid vibration path between the frame and housing. A flexible outlet bellows connects the blower discharge to the housing outlet. The final rib-defined intake chamber feeds the fan chamber, and the acoustic element sits beneath the blower inlet.
A removable polypropylene honeycomb flow straightener serves as the intake noise reduction element beneath the fan inlet. A sealed carrier routes air from the final rib-defined chamber through the honeycomb, with the cell axes parallel to the fan inlet axis. A short open plenum between the honeycomb and the fan inlet lets the cell wakes mix before the air reaches the impeller. The straightener reduces transverse flow that contributes to inlet turbulence noise.
Two internal ribs form three serial intake chambers with nominal volumes of 55, 85, and 120 millilitres. Each rib contains a rounded 15 by 20 millimetre transfer opening, and successive openings sit on opposite sides of the airflow path. At 60 litres per minute, the mean air speed through each opening is about 3.3 metres per second. The largest chamber feeds the sleeve-mounted blower through an inlet plenum above the acoustic element.
The muffling box and blower feed a heated pass-over humidifier through a sealed discharge duct. The duct rises above the reservoir's maximum fill level before entering the humidifier, and its downstream leg slopes toward the reservoir so condensate drains back into it. The rib-defined chambers and the acoustic element beneath the fan inlet operate on the dry side of the blower. The humidifier outlet connects to the breathing circuit.
A side-branch resonator beneath the fan inlet has a fixed neck, a sealed cavity, and a motor-driven piston that changes the cavity volume. The controller calculates the blade-passing frequency from the measured blower speed and the impeller blade count, then selects a piston position from a frequency calibration table. A position sensor closes the piston control loop, and the controller updates the setpoint when blower speed settles. Air flows from the final rib-defined chamber to the sleeve-mounted blower past the resonator neck.
The two housing sections sit on opposite axial sides of a joint plane perpendicular to the motor shaft. Two locating pins register the flanges, and axial screws clamp the joint.
Two molded ribs span the height of the intake chamber and terminate short of alternating sidewalls. Air passes through the two staggered gaps in sequence, then leaves the third chamber through an opening into the fan chamber.
A molded silicone sleeve grips the fan casing with an inner lip and seats in a housing groove with an outer flange. The annular web between the lip and flange carries the fan and flexes under motor vibration.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The term axially split pump 1 and/or axially split housing 2 is meant as generally used in such a way that the housing 2 is divided in parallel with the longitudinal direction of the shaft 3, this thus means in a plane which includes the longitudinal axis of the shaft 3.A · US 2016/0160871 A1 · ¶ 47
As shown in FIG. 6, an intake airflow path 150 follows a circuitous path that is indicated by arrows and flows from the canopy intake aperture 106, across the canopy intake baffle 114 to the partition panel 146, across the canopy intake floor 118 to the canopy intake exit aperture 122, into the enclosure intake cavity 70, and through the enclosure intake aperture 78 to the second chamber 58, the engine 18, and/or one or more components 22.B · US 2019/0301322 A1 · ¶ 27
An empty cell means only that no passage was reproduced there.
In this respect it is true, on the one hand, to seal the inner space of the pump with respect to the environment and, on the other hand, to seal such pressure spaces with respect to one another in the inner space of the pump in which different pressures are present in the operating state, such as is, for example the case for multi-stage pumps.A · US 2016/0160871 A1 · ¶ 7
This is in particular of advantage having regard to multi-stage pumps, as the leakage between different pressure spaces in the pump in which different pressures are present can be significantly reduced or can even be avoided.A · US 2016/0160871 A1 · ¶ 10
More particularly, the present disclosure relates to systems and methods for reducing noise emissions from a generator set.B · US 2019/0301322 A1 · ¶ 1
Current solutions to reduce noise emissions add weight and cost, and increase the footprint of the generator set.B · US 2019/0301322 A1 · ¶ 2
patent.fyi, US 2026/0355442 A1, claim 1, first published 2026-11-19T11:55:28-05:00, https://patent.fyi/US20260355442/, SHA-256 9a0a787379eda379866e3d18a757d6b773831fcccb96b8d277241cbb81ecc7ae