1.1Flow driven by inhalation
During spontaneous inhalation, the pressure drop at the patient interface opens a low-resistance inlet valve and draws room air through a filter. A separate one-way valve vents exhaled gas.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
During spontaneous inhalation, the pressure drop at the patient interface opens a low-resistance inlet valve and draws room air through a filter. A separate one-way valve vents exhaled gas.
An external gas supply conditions the gas before it reaches the apparatus inlet. An insulated transfer line with a thermostatically controlled heater keeps the gas above its dew point during delivery.
At startup, the controller loads the comfort setpoints for the water chamber heater and the heated delivery tube. An outlet sensor verifies that the gas reaches the startup targets before the controller begins the upward ramp.
Two parallel gas paths deliver the same temperature and flow at different humidity levels. A selector valve switches the patient outlet between the two conditioned streams when the user presses a button.
The blower starts at a lower pressure setpoint and raises it toward the operating setpoint at a defined rate. A pressure transducer supplies feedback to the blower controller while the humidifier and tube heater maintain fixed gas conditioning targets.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A recirculation blower sends chamber air through a membrane humidifier and into a plenum beneath the seed trays. A temperature and humidity probe in the return duct supplies the controller with a dew point measurement. After a tray change, the controller lowers the dew point target from the germination setting to a conditioning setting for cool trays, then raises it back over a timed interval.
A blower sends respiratory gas through the lumens of a hydrophobic hollow-fiber cartridge while a pump circulates heated water around the fibers. Water vapor crosses the fiber walls into the gas stream, and a downstream sensor measures gas dew point. The controller lowers the dew point target from the operational setting to the comfort setting and then restores it over time by adjusting the water heater in response to the measured dew point.
Two variable-speed blowers draw gas from a common filtered inlet and feed parallel branches that join upstream of the delivery tube. One branch passes through a humidifier and the other carries unhumidified inlet gas to the mixing junction. The controller lowers the delivered humidity to the comfort setting by increasing the unhumidified branch fraction, then gradually decreases that fraction to restore the operational humidity. Branch flow sensors support control of the mixing ratio and total flow, and an outlet humidity sensor supplies feedback on the mixed gas.
A blower feeds a heated humidifier followed by a trim heater, with a combined temperature and humidity probe near the patient connector. At the start of acclimatisation, the controller lowers the dew point target from 31 °C to 29 °C and the gas temperature target from 36 °C to 34 °C. The dew point target returns to 31 °C over 12 minutes, and the gas temperature target returns to 36 °C over 4 minutes. The humidifier heater regulates dew point, and the trim heater regulates gas temperature.
A pressure support ventilator delivers gas through a heated humidifier and a heated inspiratory tube to a vented mask. The ventilator sends its inspiratory and expiratory pressure settings to the blower controller and sends a separate acclimatisation command to the humidifier controller when assisted breathing starts. The humidifier controller lowers the dew point target to the comfort setting and restores it over the acclimatisation interval while the ventilator regulates mask pressure.
A blower supplies gas through a variable-output humidifier and a heated delivery tube with a wall temperature sensor at its coldest section. The controller lowers the dew point target to the comfort setting and starts a timed return to the operational setting. During the return, it limits the dew point target to 2 °C below the measured wall temperature and resumes increasing the target as that section warms. A temperature and humidity probe at the delivery outlet supplies feedback for humidifier control.
A pressure regulator lowers the outlet pressure of a compressed breathing gas reservoir. A flowmeter and a metering valve set the continuous flow to the patient circuit.
A brushless motor drives a centrifugal impeller that takes in filtered air. A downstream flow sensor supplies feedback for motor speed adjustments that maintain the selected flow rate.
A resistive heater warms water through the metal base of a removable chamber. Gas passes over the water surface and picks up water vapor before entering the delivery tube.
Breathing gas flows through hollow fibers surrounded by circulating warm water. Water vapor crosses the fiber walls into the gas stream while the walls retain liquid water.
At acclimatisation startup, the controller lowers the delivery temperature setpoint from 34 °C to 30 °C and waits for an outlet thermistor to confirm the lower temperature. It then raises the setpoint by 0.2 °C per minute for 20 minutes and adjusts heater power using thermistor feedback.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A flow of gases is provided through the chamber 5 by an integrated blower unit contained within the housing 10.A · US 2010/0043791 A1 · ¶ 10
A flow generator 10 produces pressurized airflow, which passes through a lumen of a first air conduit section 12 connecting the flow generator to a humidifier 27, where it is humidified and then continues traveling through a lumen of an air conduit section 13 to a patient interface 14, such as a mask or a nasal cannula.B · US 2017/0216552 A1 · ¶ 64
The gases enter the humidifier chamber, and are humidified as they pass over a volume of heated water contained in the chamber.A · US 2010/0043791 A1 · ¶ 6
The user of the device may set a predetermined required value (preset value) of humidity or temperature of the gases supplied to patient 1, via a control interface such as a dial or buttons on a control pad or panel.A · US 2010/0043791 A1 · ¶ 12
An empty cell means only that no passage was reproduced there.
In order to counteract this side effect, it is usual for the air that is provided to a user to be humidified, by adding a humidification chamber or similar into the gases stream before the gas is provided to the patient.A · US 2010/0043791 A1 · ¶ 6
However, full-face masks, nasal masks, nasal cannulas, oral mouthpieces, tracheostomy connections, or any other suitable interface can be used with these systems.A · US 2010/0043791 A1 · ¶ 9
However, they either lack humidification or, if they include it, it requires extra bulk.B · US 2017/0216552 A1 · ¶ 6
The bulk of the water chamber is not compressible, and therefore inhibits portability and travel.B · US 2017/0216552 A1 · ¶ 7
patent.fyi, US 2026/0355449 A1, claim 1, first published 2026-11-19T11:55:28-05:00, https://patent.fyi/US20260355449/, SHA-256 8f4775df3fe8a5e96f35d6fe130ac456d261278c601ac037a903ac37ba230b2c