1.1Continuous tapered shaft wall
A thermoplastic tube has a constant lumen diameter and a wall that thins gradually toward the tip. The thicker proximal wall transmits axial push, and the thinner distal wall lowers bending stiffness.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A thermoplastic tube has a constant lumen diameter and a wall that thins gradually toward the tip. The thicker proximal wall transmits axial push, and the thinner distal wall lowers bending stiffness.
A thin polymer sleeve spans the slots and bonds to uncut shaft lands at either end. The inside edges of the slots close during bending and contact at a preset curvature, increasing resistance to further bending.
A flexible polymer compounded with tungsten powder forms the full distal tip around the lumen. The tungsten particles attenuate X-rays along the length of the tip, producing a visible distal reference.
A short tantalum wire runs parallel to the shaft axis and sits within the polymer jacket at the proximal reference location. The wire produces a localized line on the fluoroscopic image while leaving the lumen open.
A thin metal band slips over the shaft and bonds to its outer surface with a thin cured adhesive layer. A polymer jacket covers the band, and tapered jacket transitions smooth the change in outer diameter at both band edges.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A hollow metal shaft carries transverse gaps filled by an overmolded elastomer jacket. A distal radiopaque band identifies the sampling inlet, and a proximal radiopaque band sits in a circumferential shaft groove and identifies the start of the flexible section. An external pump draws fluid through the shaft while radiographic images locate the two bands inside an opaque process line. On tight bends, the gaps narrow on the compression side until opposing faces bear through the compressed elastomer and increase the moment required for further bending.
A tungsten-filled thermoplastic annulus serves as the proximal radiopaque band, and a solid metal band remains at the distal end. The composite annulus seats in the proximal circumferential groove and sits flush with the surrounding shaft surface before jacketing. A separate elastomer jacket fills the shaft gaps, and opposing gap faces progressively compress the elastomer as the shaft bends, increasing the incremental bending stiffness.
A liquid silicone rubber jacket replaces a melt-processed thermoplastic jacket around the gapped metal shaft. A removable mandrel supports the bore during injection molding, and the silicone cures in the gaps and around the distal radiopaque band and the proximal band seated in its circumferential groove. As the shaft bends, opposing gap faces compress the silicone, and the surrounding metal and jacket progressively restrict its lateral deformation, increasing the incremental bending stiffness.
A 0.90 mm outer diameter metal tube with a 0.10 mm wall carries 24 transverse slots at a 0.50 mm axial pitch. The slots alternate between axial widths of 40 and 80 micrometers, and successive slots rotate 90 degrees around the tube, leaving an intact wall sector at each slot. A single elastomer jacket fills both slot widths over a removable lumen mandrel, and the shaft carries a distal radiopaque band plus a proximal radiopaque band seated in a circumferential groove. As curvature rises, the narrower slots on the compression side confine their elastomer fill at smaller local rotations than the wider slots, producing a staged increase in bending stiffness.
A fiber optic pressure sensor mounts in a short distal tip with its sensing diaphragm exposed to fluid through a side port. The optical fiber runs through the shaft lumen to an external optical interrogator, and a sealed feedthrough behind the sensor isolates the pressure port from the lumen. An elastomer jacket fills the shaft gaps and resists further bending as the gaps narrow on the compression side. A distal radiopaque band sits beside the pressure port, and a proximal radiopaque band seats in a circumferential shaft groove.
A rotary fixture indexes the shaft under a laser while a telecentric camera measures each through-wall gap against a calibrated image scale. Software compares the measured width with the drawing value and commands a trim pass on an undersized gap when its width falls below the lower tolerance limit. The assembled shaft carries a distal radiopaque band, a proximal radiopaque band in a circumferential groove, and an overmolded elastomer jacket that fills the measured gaps. A motorized bend fixture records moment against angle over a fixed gauge length, and software checks the incremental stiffness at two specified angles against production limits.
A tube with uniform slot geometry and a compliant jacket operates over a bend range in which the slot edges remain separated and the materials stay in their linear elastic range. Over that range, the bending moment rises in proportion to the bend angle.
A laser cuts short circumferential slots into a stainless steel tube. Successive slot rows rotate around the shaft axis, leaving metal bridges that carry axial loads and flex as the shaft bends.
A heated polyurethane jacket reflows into the laser-cut slots while a removable mandrel preserves the lumen. At larger bend angles, the narrowing slots confine the nearly incompressible polyurethane and increase the incremental bending stiffness.
A short platinum-iridium ring fits around the distal shaft beneath the polymer jacket. The ring attenuates X-rays to mark the distal location under fluoroscopy.
A shallow annular groove in the shaft matches the width of a tantalum marker band. Radial swaging seats the band in the groove, where the groove shoulders restrain axial movement.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In catheter designs, radiopaque marker bands or catheter tips are often attached to the catheter for this purpose. For example, radiopaque marker bands have been placed on the inner shaft of the catheter on either side of the stent mounted to the balloon to mark the ends of the stent during delivery.B · US 2017/0231790 A1 · ¶ 7
Preferably, the rotation-locking device additionally comprises a locating groove for locating said retention ring, this groove being formed on a radially inner end face of the shaft.A · US 2006/0291953 A1 · ¶ 33
An empty cell means only that no passage was reproduced there.
The present invention relates to the technical field of maintaining a component inside an end of a hollow shaft or of a journal of a turbomachine such as an aircraft engine, said component possibly being a bearing outer race.A · US 2006/0291953 A1 · ¶ 1
More specifically, the invention relates to a device for rotationally locking a clamping nut for a component on an end of a hollow shaft.A · US 2006/0291953 A1 · ¶ 2
To assist in accurate placement of the catheter and stent at the lesion site it is useful to visually monitor the catheter as it advances through a vessel.B · US 2017/0231790 A1 · ¶ 7
One problem with such bands it that they locally stiffen the catheter shaft and thereby impart an undesirable discontinuity thereto as the metal radiopaque bands are relatively inflexible compared to a polymer balloon catheter shaft.B · US 2017/0231790 A1 · ¶ 7
patent.fyi, US 2026/0355459 A1, claim 1, first published 2026-11-19T11:55:28-05:00, https://patent.fyi/US20260355459/, SHA-256 471acda550a9600403122a6ba4baeb25733c25ba960d1ef690fa24ac303bed6a