1.1Direct manual instrument translation
The instrument hub slides on a rail aligned with the insertion axis. The operator grips the hub to set insertion depth, and a graduated scale beside the rail shows hub position.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The instrument hub slides on a rail aligned with the insertion axis. The operator grips the hub to set insertion depth, and a graduated scale beside the rail shows hub position.
A powered roller and a spring-loaded idler feed the flexible shaft through a fixed curved liner. The liner supports the shaft against buckling and sets the exit direction.
A linear encoder measures carriage position while a servo compares the measurement with the commanded depth. The servo adjusts motor current to apply corrective axial force when an external load displaces the carriage.
The motor turns a low-lead trapezoidal screw, and a captive nut translates the instrument carriage on linear rails. The thread lead angle stays below the effective friction angle under the specified load and lubrication conditions, so axial load on the nut does not drive screw rotation.
The controller estimates external axial force from motor current and carriage acceleration after accounting for drivetrain friction. A proportional electromagnetic brake increases resisting torque as the estimated disturbance rises, and the same control law runs during travel and at rest.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A belt-driven vertical carriage carries a pipetting head above a rack of sample tubes. A spring-applied rail brake on the carriage grips a stationary guide rail. The controller engages the brake when the vertical drive enters its idle mode, so forces from tip ejection or contact with a tube do not displace the carriage.
A pair of oppositely wound wrap springs replaces the carriage brake and surrounds a drum keyed to the insertion drive screw. One end of each spring anchors to the manipulator frame, and an electromagnetic release collar opens both springs during powered travel. When the drive enters idle mode, the controller deenergizes the release coil, and the springs tighten against the drum under back-driving torque in either direction.
A direct-drive linear motor replaces the rotary motor and screw transmission, with its magnet track fixed to the frame and its moving coil attached to the instrument carriage. A linear encoder supplies position feedback during commanded travel. When the controller enters idle mode, it engages a spring-applied caliper on a stationary brake rail and disables motor current after a switch confirms caliper closure.
A motorized carriage has 25 mm of insertion travel and a maximum commanded speed of 5 mm/s. A spring-applied carriage brake grips the stationary guide rail and has a specified engagement time of 20 ms or less after coil power is removed. At the end of a move, the trajectory generator commands zero velocity for 40 ms before the controller enters idle mode and removes brake coil power.
A motorized instrument insertion stage mounts to a procedure table on an adjustable bracket, with its brake mounted at the proximal end of the stage. A fluoroscopy controller supplies an acquisition request to the insertion controller through a digital handshake. On receiving the request, the insertion controller completes a controlled stop, enters idle mode, and engages the brake. A brake position switch confirms engagement before the insertion controller returns an acquisition permit.
A software sequencer executes a stored procedure script containing insertion moves and timed dwell steps. The sequencer dispatches move steps to the insertion drive and sets the axis to idle when it dispatches a dwell step. The idle state engages a carriage brake, and the dwell timer starts when a switch confirms brake engagement. The sequencer advances to the next step when the timer expires.
A spring presses a friction disc against the housing when the motor supplies no torque. Ramps on the input coupling lift the disc as the motor starts in either direction, and the spring reapplies the disc when input torque drops below the release threshold.
A brushless motor rotates a ball screw mounted parallel to the insertion axis. A ball nut fixed to a rail-guided carriage converts screw rotation into axial travel of the instrument mount.
A stationary magnet track and a moving coil generate thrust along the insertion axis. A linear encoder measures carriage position, and a servo regulates coil current to move the instrument mount to the commanded depth.
Belleville washers press opposed friction pads against a stationary rail parallel to the insertion axis. An energized coil retracts the pads, and the washers reapply them when coil current is removed.
The controller selects the motion state when the insertion trajectory generator requests axial travel and energizes the brake release before allowing the drive to move. After the trajectory ends and encoder velocity falls below a stop threshold, the controller selects the stationary state and de-energizes the release coil to hold against external axial force.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A motor 1 is connected via its outgoing shaft to an automatic gearbox 9, which normally enables the vehicle to be driven with several different gears between the motor 1 and driving wheels 8.A · US 2006/0279137 A1 · ¶ 17
The mechanical brake is applied at the train station or at a station stop, as soon as the vehicle is at a standstill. The mechanical brake is then utilized as holding brake.B · US 2009/0234548 A1 · ¶ 2
This object is solved in accordance with the invention by providing a control system of the electric machine to so control the operation of the electric machine that the position of the rotor in the stator remains constant even when exposed to an external torque.B · US 2009/0234548 A1 · ¶ 6
An empty cell means only that no passage was reproduced there.
A problem with this solution is that the most favorable braking sequence cannot be selected which takes into account brake wear, gear selection and distance to the vehicle in front.A · US 2006/0279137 A1 · ¶ 7
Against the background of the above, the task of the invention is thus to make it possible to control a vehicle's braking sequence in a more optimal way, in a vehicle with cruise control of the ACC type (Adaptive Cruise Control), with acceleration function, brake function and distance measurement to the vehicle in front.A · US 2006/0279137 A1 · ¶ 8
The invention is therefore based on the object to provide a holding brake for track-bound motor vehicles, which consumes less energy than a pneumatic holding brake and which ensures greater riding comfort.B · US 2009/0234548 A1 · ¶ 5
As a result, no wear is advantageously encountered during operation of the holding brake according to the invention since the holding forces are produced magnetically and not by mechanical forces.B · US 2009/0234548 A1 · ¶ 7
patent.fyi, US 2026/0355460 A1, claim 1, first published 2026-11-19T11:55:28-05:00, https://patent.fyi/US20260355460/, SHA-256 0b443bd796e85890ea4691af8db37c24c963f32f7aaf339fecd93c285ee54964