1.2Motor on a separate frame
The motor bolts to a drive frame, and a flexible rotary shaft couples its output to the lead screw. Bearings in the catheter holder support the screw and carry the axial loads from the followers.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The motor bolts to a drive frame, and a flexible rotary shaft couples its output to the lead screw. Bearings in the catheter holder support the screw and carry the axial loads from the followers.
The drum has two grooves of equal radius that take up the two drive cables in opposite directions. A return spring keeps each cable under tension, and linear guides constrain the carriages to axial travel.
A shaft with a uniform outside diameter carries a right-hand thread on one section and a left-hand thread of equal lead on the other. Matching nuts run on separate linear guides and travel equal distances in opposite directions per screw revolution.
An open-sided carriage carries two bearing rollers that contact opposite flanks of the first helical groove. Eccentric roller mounts set the clearance, and a linear rail restrains the carriage from rotating with the screw.
A reduction gear pair transfers rotation from the screw shaft to a pinion that meshes with a straight rack on the second carriage. The gear ratio and pinion pitch diameter set the carriage travel per motor revolution.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A motor on the spectrometer frame turns a stepped lead screw with two threaded portions of different major diameters. Each internally threaded follower carries a filter flag and slides in a rectangular slot in the frame that prevents it from rotating. Turning the screw moves the flags across two parallel light paths so that both filters enter or leave their respective paths together.
Two recirculating ball nuts replace the internally threaded sliding followers, and the stepped screw has matching helical ball grooves on its two diameters. Each nut mounts in a rectangular carriage captured in a longitudinal channel in the holder. As the screw turns, the balls roll between the screw and nut grooves and return through a passage in the nut, while the carriage transfers axial motion to a catheter pull wire.
Each one-piece follower is replaced by two axially spaced acetal nut segments threaded to fit its assigned screw diameter. The segments sit in a keyed carriage with one segment fixed axially and the other free to slide a short distance. A compression spring between the segments presses them against opposing thread flanks, reducing lost motion at the carriage when the screw reverses.
The stepped screw has major diameters of 6 mm and 4 mm, with 14 mm of usable thread on each portion. Each 5 mm long follower operates between carriage stops spaced to provide 4 mm of axial travel. With a lead of 0.5 mm per revolution, the motor turns the screw eight revolutions between the stops, and a bearing pair in the holder fixes the screw axially.
A linear insertion stage carries the holder, motor, stepped screw, and both followers as one assembly. A clamp on the moving holder grips the catheter shaft, and each follower connects to a pull wire through a clevis. The insertion stage moves the shaft and articulation assembly together, while the screw moves the pull wires relative to the shaft to bend the tip.
An inline strain gauge load cell connects each follower to its pull wire, and a rotary encoder measures screw angle. A controller zeros the load cells before the wires are tensioned and records both forces against screw angle during articulation. The controller stops the motor when either force exceeds its configured limit and permits release motion only in a direction that the measured force confirms is unloading the affected wire.
An anodized aluminum holder has two coaxial bearing seats and a flat mounting face for the motor. A doweled end plate closes one bearing seat and provides access to the screw during assembly.
Four screws clamp the flange of a brushless motor to the holder, and a machined pilot centers the motor shaft. A bellows coupling transmits torque to the lead screw and accommodates small shaft misalignment.
A one-piece stainless steel screw has a 6 mm major diameter on its right-hand threaded section and a 4 mm major diameter on its left-hand threaded section. Both sections have a lead of 1 mm per revolution, so the guided followers travel equal distances in opposite directions.
Two internally threaded polymer nut segments engage the second threaded section and slide axially in a keyed carriage that restrains their rotation. A compression spring pushes the segments apart to keep them in contact with opposing thread flanks during direction changes.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A motor assembly for a convection oven includes a motor mount bracket and a motor.A · US 2023/0013590 A1 · abstract
The motor is selectively attached to the motor mount bracket by inserting a respective locking flange into a respective slot and twisting the motor.A · US 2023/0013590 A1 · abstract
For some applications, inner shaft 68 defines a threaded outer surface 76 at its distal end, and the inner surface of distal device interface 74 (which is described hereinabove is typically a flange) and/or medial shaft 66 is correspondingly threaded. The threaded inner surface of distal device interface 74 and/or medial shaft 66 acts as a nut, such that rotation of the distal end of the inner shaft causes the inner shaft to advance distally with respect to the distal device interface 74.B · US 2024/0238089 A1 · ¶ 127
An empty cell means only that no passage was reproduced there.
However, assembly of the motor to the bracket is cumbersome and tedious, often including a plurality of fasteners.A · US 2023/0013590 A1 · ¶ 3
In particular, a mounting structure for motors with reduced parts and labor would be useful.A · US 2023/0013590 A1 · ¶ 4
The present invention relates to medical apparatus and methods, and specifically to apparatus and methods for percutaneously delivering a medical device to a deployment location within a subject's body, such as an atrioventricular valve.B · US 2024/0238089 A1 · ¶ 4
patent.fyi, US 2026/0355462 A1, claim 1, first published 2026-11-19T11:55:28-05:00, https://patent.fyi/US20260355462/, SHA-256 e30384e48a6559df287cb143824295c1084cfd62241a445e7d60a8ad2f3baed6