1.2Single hollow needle
A single-bore hub feeds the lumen of one hollow needle. The actuator reciprocates the needle, and the operator moves the handpiece across the target site to distribute the application points.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A single-bore hub feeds the lumen of one hollow needle. The actuator reciprocates the needle, and the operator moves the handpiece across the target site to distribute the application points.
Two heat-sealed polymer films form a flat reservoir with one outlet fitting. A downstream pump draws medium through the fitting, and the films collapse together as the reservoir empties.
A captive cover holds both cartridges on a slide-in carrier, and a housing latch retains the carrier. Releasing the latch withdraws both cartridges together, and a mechanical interlock allows the cover to open once the carrier is out.
The actuator completes a stroke and holds the manifold at the extended position while the pressure inducer delivers a metered pulse through the hollow needles. A shutoff valve closes and the pressure inducer stops before the actuator retracts the manifold.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A fixture clamps a synthetic leather coupon over a replaceable elastomer backing. A separately mounted dye cartridge holds liquid dye in a vented serpentine cavity and feeds a distribution channel along the base of the solid needles. The controller pressurizes the cartridge while reciprocating the needle manifold, and the wetted needles carry dye into the coupon through the punctures.
A linear voice coil replaces the rotary motor and cam of a reciprocating drive. The coil mounts in the housing, and its moving magnet connects to the needle manifold through a detachable drive pin. Two parallel leaf springs guide the moving assembly along the needle axis, and the controller alternates coil current while energizing the pressure inducer.
A three-roller peristaltic pump draws media through the exit port of the serpentine reservoir while a filtered vent admits replacement air. The media cartridge carries a flexible outlet tube that snaps into the pump track and mates with a fluid socket connected to the needle manifold. The controller runs the pump rotor during reciprocation, and opening the pump track releases the tube for media cartridge removal.
A bench fixture holds a synthetic skin pad under a cartridge with four solid needles at 1 mm center-to-center spacing. The actuator drives the manifold through a 0.5 mm stroke at 20 cycles per second in bursts of 10 cycles separated by 250 ms pauses. A pressure regulator supplies 10 kPa gauge pressure at the reservoir vent during each burst and returns the vent to ambient pressure during each pause.
A motorized two-axis positioning stage carries a clamped test coupon beneath the fixed device housing. The media and needle cartridges attach independently to the housing, with the needle axis perpendicular to the stage. At each programmed coordinate, the stage controller sends an in-position signal that triggers a timed burst of needle reciprocation and reservoir pressurization before the stage advances.
An inline thermal flow sensor sits in the stationary fluid path between the media cartridge outlet and the flexible connection to the reciprocating manifold. The controller averages the sensor output over complete needle cycles and adjusts an electronic air pressure regulator at the reservoir vent to maintain a programmed mean flow rate. The controller limits regulator pressure and stops both flow and reciprocation if measured flow stays below the programmed minimum while pressure is at the limit.
A cable carries motor current from the console to the handpiece and returns position signals from a Hall sensor. The controller uses those signals to regulate the reciprocation rate.
A porous wick draws a low-viscosity aqueous medium from the reservoir to an applicator pad in the needle cartridge. The solid needles pass through the wetted pad on each stroke and carry a surface film to the target site.
The housing contains a direct-current motor and a controller board with a motor driver. An eccentric pin on the motor shaft drives a guided slider, and the pin offset sets the slider travel.
A molded polymer manifold divides the inlet flow among equal-length radial channels. Each channel feeds one hollow stainless steel needle seated in a socket and bonded around its outer wall.
A welded polymer cover closes a serpentine groove molded into the cartridge body. A hydrophobic membrane at one end admits replacement air as medium exits through a fitting at the other end.
The controller drives a reciprocating actuator and a peristaltic pump through separate outputs during the same application interval. The actuator drive sets the stroke frequency, and the pump drive sets the tubing compression cycle rate.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In various embodiments, the durable housing 30 may include an interior volume for housing the motor 84, the drive device linkage portion 82, other electronic circuitry, and a power source (not shown in FIGS. 5A, 5B, and 5C).A · US 2009/0171324 A1 · ¶ 90
The multi-chamber syringe module also includes a needle manifold that is rotatably coupled to the multi-chamber cartridge. The multi-chamber syringe module further includes a luer fitting hub fixedly coupled to the needle manifold at a first end and selectively coupled to a biopsy needle at a second end.B · US 2020/0397990 A1 · abstract
The durable housing 30 of the delivery device 12 may support a drive device (not shown in FIG. 2), including a motor and a drive device linkage portion, for applying a force to fluidic media within the reservoir 40 to force fluidic media out of the reservoir 40 and into an infusion path, such as the infusion path 50, for delivery to a user.A · US 2009/0171324 A1 · ¶ 78
In this embodiment of fluid chamber 110, the user squeezes the walls of fluid chamber 110 to pump the contents—air, saline or some other fluid—through chamber fitting 120, needle manifold 104, luer fitting hub 106, and a biopsy needle.B · US 2020/0397990 A1 · ¶ 50
The connector 56 of the infusion path 50 may be connectable to the port 41 of the reservoir 40. In various embodiments, the disposable housing 20 is configured with an opening near the port 41 of the reservoir 40 for allowing the connector 56 of the infusion path 50 to be selectively connected to and disconnected from the port 41 of the reservoir 40.A · US 2009/0171324 A1 · ¶ 75
An empty cell means only that no passage was reproduced there.
Embodiments of the present invention relate generally to systems and methods with reservoirs and, in specific embodiments, to systems and methods allowing for pressure equalization of fluidic media contained within the reservoirs.A · US 2009/0171324 A1 · ¶ 2
However, one of the problems with pump type delivery devices is that a bolus of fluidic media could be delivered inadvertently to the patient in a case where the reservoir of fluidic media is pressurized.A · US 2009/0171324 A1 · ¶ 8
This disclosure relates generally to a syringe device, and more particularly to a multi-chamber syringe for use with a biopsy needle.B · US 2020/0397990 A1 · ¶ 2
The attachment and reattachment adds time to each FNA procedure.B · US 2020/0397990 A1 · ¶ 7
patent.fyi, US 2026/0355484 A1, claim 1, first published 2026-11-19T12:21:55-05:00, https://patent.fyi/US20260355484/, SHA-256 458a8e0fa794535b3a9ad020eff6e6ce90b50248c49ec470639371095ae7d35f