1.1Open flexure needle guide
Two parallel leaf springs connect a moving needle carrier to an open frame and constrain its stroke along the needle axis. A stationary capillary places a droplet on the exposed needle near the end of its return stroke.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two parallel leaf springs connect a moving needle carrier to an open frame and constrain its stroke along the needle axis. A stationary capillary places a droplet on the exposed needle near the end of its return stroke.
A carriage on two external guide rods holds the needle parallel to the pigment channel. An outlet at the distal end of the channel faces the needle path and forms a meniscus that the needle contacts on each stroke.
A transverse yoke joins the drive plunger to the needle carrier. The plunger and carrier travel equal axial distances in separate parallel guides.
A return stop keeps the tip distal to the outlet at maximum retraction. Two lateral contact feet establish a skin contact plane that the tip clears during retraction and crosses during extension.
A sintered polymer wick passes through a sealed reservoir slot and ends beside the exposed needle shaft. Capillary action replenishes pigment at the wick face, and the moving shaft picks up a film on contact.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A reciprocating hollow needle and its attached plunger run in a guide channel above a conveyor for paper blanks. A radial reservoir outlet registers with a local slit on the plunger during the advance stroke, and a drilled passage carries marking fluid from the slit to the needle bore. An optical edge detector triggers the stroke so the needle tip contacts the blank at a fixed offset from its leading edge. The plunger surface closes the reservoir outlet on either side of the alignment zone.
A sealed collapsible polymer pouch serves as the product reservoir. A rigid outlet fitting bonded to the pouch seats against a gasket at a radial bore in the channel wall, and the fitting and bore form the reservoir lumen. A spring-loaded plate behind the pouch maintains feed pressure as the pouch collapses. The plunger slit admits fluid during alignment with the bore, and the solid plunger surface closes the bore outside that interval.
A normally closed diaphragm valve replaces the slit valve at the reservoir lumen. A spring presses the diaphragm against an annular seat, and a roller follower runs on a raised cam segment carried by the needle plunger. A rocker links the follower to the diaphragm stem and lifts the diaphragm while the cam segment passes under the follower between the stroke endpoints. Fluid passes through the open seat and into the channel, and the spring reseats the diaphragm when the follower leaves the cam segment.
A linear stage moves the needle and plunger through a 3.0 mm stroke in a bench fixture containing water-based test dye. The reservoir outlet is a 0.4 mm circular bore, and the local plunger slit spans 0.6 mm axially and at least 0.8 mm across the outlet face. The slit center aligns with the bore center 1.2 mm from full retraction, giving a nominal overlap window from 0.7 to 1.7 mm of travel. The stage crosses the window at 30 mm/s on the advance stroke, producing about 33 ms of overlap.
A peristaltic pump transfers fluid from a bulk container through flexible tubing to a fill inlet in a small reservoir mounted beside the channel. Upper and lower level sensors on the reservoir start and stop the pump to maintain the operating fill level. A separate radial lumen connects the reservoir to the channel, where the translating plunger slit opens the fluid path during the intermediate supply interval. A vent above the upper sensor allows displaced air to leave as the reservoir fills.
A direct-drive linear actuator moves the needle and plunger assembly, and a linear encoder measures plunger position relative to the channel. The controller uses a stored alignment position where the plunger slit centers on the radial reservoir lumen. On the advance stroke, the controller holds the plunger at this position for a programmed dwell before completing extension. The return stroke traverses the alignment zone at a fixed speed, and the plunger closes the lumen at both endpoints.
Three stainless steel needles sit parallel in a triangular array within the channel. A common hub holds the shafts with their tips at the same axial height.
A narrow circumferential slit in the plunger aligns with the radial reservoir port during intermediate travel. A shallow axial passage connects the slit to the needle side of the plunger, and cylindrical lands on either side of the slit cover the port outside the supply interval.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The needle assembly includes a housing comprising a tubular longitudinal channel and a guide surface.B · US 2020/0276429 A1 · ¶ 22
A plurality of thin needle wires constitute a cylindrical shape to form a round needle head, or a plurality of thin needle wires are arranged side by side to form a flat needle head. A needle tip equipped with around or rhombus opening is used corresponding to the round needle head, and a needle tip equipped with a rectangle opening is used corresponding to the flat needle head.A · US 2013/0226211 A1 · ¶ 5
The needle bundle includes one or more needles longitudinally reciprocally movable in the channel and is biased against the guide surface across the grooves such that, during longitudinal reciprocal movement of the needle bundle, the needle bundle maintains contact with the guide surface and the liquid stored in the grooves for drawing the liquid out of the grooves by capillary action.B · US 2020/0276429 A1 · ¶ 22
The needle actuator is activated to drive the drive shaft 1035 and consequently needle shaft 1240 and tip portion 1210 of the needle bundle 1200 downward. After each downward stroke, the resilient band 1300 is stretched and pulls the tip portion 1210 back up once the drive shaft 1035 stops the downward movement and moves upward.B · US 2020/0276429 A1 · ¶ 130
The ink reservoir is provided with at least one ink chamber with capillary action. At least one ink guiding passage connects the capillary ink chamber with the needle tip opening.A · US 2013/0226211 A1 · abstract
An empty cell means only that no passage was reproduced there.
The needle tip equipped with a rectangle opening can also be designed to be open, that is, designed as a rectangle slot.A · US 2013/0226211 A1 · ¶ 5
During tattooing, adding ink frequently will bring trouble and inconvenience to the tattooists, so, break or insufficiency of ink supply will frequently occur during making tattoos.A · US 2013/0226211 A1 · ¶ 8
The section of the needle opening for feeding ink to the sharp end of the needle is the feed section.B · US 2020/0276429 A1 · ¶ 7
In order to avoid the leakage of ink, tattooists have to add little ink each time, which increases the frequency of adding ink and results in ink failure or insufficient ink provision.B · US 2020/0276429 A1 · ¶ 8
patent.fyi, US 2026/0355487 A1, claim 1, first published 2026-11-19T12:21:55-05:00, https://patent.fyi/US20260355487/, SHA-256 a1a38520f1a6677e12116002e34a07718d03c726bfadd633e02ebcf4295c7778