1.1Closed bore connector retainer
The connector inserts axially into the bore until its shoulder contacts an annular stop. A threaded retaining collar clamps the shoulder against the stop while leaving the mating end exposed.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The connector inserts axially into the bore until its shoulder contacts an annular stop. A threaded retaining collar clamps the shoulder against the stop while leaving the mating end exposed.
Locating pins seat both connector holders against a common datum with their centerlines coaxial. A linear guide constrains the movable platform to axial travel while a lead screw advances it to engage the connectors.
A spur pinion drives an annular gear concentric with the connector. An axially sliding keyed sleeve transmits torque from the annular gear, and a lead screw translates the sleeve along the connector axis.
The movable platform rests against a locating stop, and a spring-centered holder lets the second connector shift radially. A separate linear actuator advances the holder into a tapered guide that bears on the connector shell and centers it before the fluid interfaces meet.
The fixed platform supports the first connector in a keyed sleeve that slides along the common connector axis. A motor-driven lead screw advances the sleeve to a mechanical stop that sets the engagement depth.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A fixed slotted cradle holds a capped sample branch from a dairy process line, and a movable slotted cradle holds the capped inlet of a disposable sample bag. Both cradles sit inside a closed chamber with sealed tubing pass-throughs and a dedicated gripper for each cap. After the grippers withdraw the caps, the movable cradle shifts laterally to align the connector axes and advances axially to engage the mating ends. An inclined drive gear turns and advances the threaded collar, and the controller opens the upstream sample valve after an end-of-travel switch confirms that the collar is seated.
A hollow-shaft servo and a ball-screw linear stage replace the inclined drive gear. The servo sits on the linear stage with its shaft coaxial with the connector, and a split socket on the shaft grips the threaded collar around the tubing. Once the movable platform aligns and engages the connector ends, the controller commands one thread lead of axial travel per servo revolution. A spring behind the socket absorbs small feed errors, and the controller stops both axes when the collar reaches its seating torque within the expected travel window.
A motorized swing arm on a vertical pivot carries a short axial rail and a slotted connector cradle in place of two stacked linear stages. The curved arm travel brings the moving connector onto the fixed connector axis at a repeatable mechanical stop, with the rail parallel to that axis. A leadscrew advances the cradle along the rail until the connector noses touch. An inclined drive gear rotates and advances the coupling collar while the pivot actuator holds the arm against the stop.
Four fixed slots and four matching movable slots sit on 40 mm centers, with one inclined drive gear and motor per connector pair. The common movable platform has 30 mm of lateral travel and 15 mm of axial travel, with guides that keep the slot rows parallel. Each movable slot sits on a spring-loaded axial mount with 2 mm of compliance to absorb differences in initial engagement depth. The controller aligns and advances the four pairs together, then drives each collar to its individual seating torque.
An automated connector module interfaces with a pressure-decay tester containing a pressure transducer, a test source, and a vent valve. Two motorized pinch valves isolate the connected tubing segment, and a preinstalled branch within that segment links the test source to the closed fluid path. After the drive gear seats the collar, the tester applies a preset pressure, isolates the source, and measures the pressure change over a fixed interval. The controller depressurizes the segment through the test branch and opens the pinch valves only when the measured decay falls within the configured limit.
Two orthogonal cameras view molded reference marks on the connector bodies through chamber windows, and an axial load cell sits behind the fixed cradle. The controller estimates lateral and vertical offsets from the camera images and corrects them with motorized transverse axes before advancing the movable cradle axially. If the load exceeds a stored limit before the expected engagement position, the controller retracts the cradle and measures alignment again. Once engagement passes the force and position checks, the controller runs the inclined drive gear and uses measured collar travel and gear torque to confirm seating.
A machined polymer insert forms an open slot with a flat that mates with a flat on the connector shell. An axial shoulder takes the insertion load, and a spring clip retains the connector in the slot.
Two stacked linear stages carry the second connector slot on crossed roller guides. One stage moves perpendicular to the connector axis, and the other moves parallel to it.
The controller drives a stepper motor and lead screw to move the platform transversely. A linear encoder reports the platform position, and the controller stops the stage at the calibrated coordinate where the connector axes coincide.
After alignment, the controller drives an axial ball screw stage to advance the movable platform until the connector lead-ins engage. A load cell measures axial force, and the controller stops the stage when both the position and force are within their specified engagement ranges.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The first or front motorized linear actuator 44 located proximate the head end 2 of the adjustable bed base 12 extends between a first or front slotted mounting bracket 48 secured to the hollow cross member 22 of the stationary frame 14 and a head mounting bracket 58 secured to a U-shaped metal brace 50 secured to the underside of the head deck board 32.B · US 11,930,932 B2 · ¶ 29
The opening 139 is configured to receive the inner blade tube 134 such that the inner blade tube 134 is fixed to the armature 138. The cannulated armature 138 is configured to be driven by the solenoids 130A, 130B to reciprocate between the endcaps 133, 135.A · US 10,517,629 B2 · ¶ 27
An empty cell means only that no passage was reproduced there.
This reciprocating motion has limitations in that it is often complex relative to oscillatory or rotational cutting, and it doesn't lend well to curved devices.A · US 10,517,629 B2 · ¶ 2
Accordingly, there is a need to provide improved and reliable medical device configurations.A · US 10,517,629 B2 · ¶ 4
It is therefore an objective of this invention to provide an adjustable bed base which protects one or more linear actuators of the adjustable bed base.B · US 11,930,932 B2 · ¶ 7
It is further an objective of this invention to provide an adjustable bed base which provides improved access to electronic and mechanical components located underneath the deck.B · US 11,930,932 B2 · ¶ 8
patent.fyi, US 2026/0355492 A1, claim 1, first published 2026-11-19T12:21:55-05:00, https://patent.fyi/US20260355492/, SHA-256 c4d989d7d88299bd19c0cda4f9083a603c8753135f09818d5ad6a30f5be97ded