1.4Controls on the stimulation unit
A start button and two amplitude buttons connect directly to inputs on the unit's microcontroller. The microcontroller reads the button states and sets the output driver's pulse timing and current amplitude.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A start button and two amplitude buttons connect directly to inputs on the unit's microcontroller. The microcontroller reads the button states and sets the output driver's pulse timing and current amplitude.
Two metal plates sit beneath a continuous polymer film, which forms a capacitive interface between each plate and the foot. Alternating voltage across the plates drives displacement current through the film at both interfaces and alternating current through the intervening tissue.
An insulated implanted lead carries two exposed contacts positioned next to the target nerve. An implanted pulse generator drives biphasic current between the contacts through the surrounding tissue.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A close-fitting aquatic boot holds two hydrogel electrodes against the foot, with a molded silicone web separating the electrodes. Each electrode sits within a raised sealing rim that presses against the skin, and sealed leads connect the electrodes to a battery-powered waveform generator in a watertight ankle housing. During pool exercises, a deck-side remote sends commands over an inductive link to a receiver coil positioned near the waterline. The generator checks electrode impedance before applying the selected waveform.
Two carbon-filled silicone pads replace the skin-contact electrodes and sit in separate recesses in a nonconductive silicone cuff. Each pad has a molded-in terminal on its back and a ribbed face that contacts the skin. Separate insulated leads connect the terminals to a battery-powered waveform generator, which applies pulses across the pads when its receiver decodes a remote command.
A flexible foot wrap carries four 20 mm by 25 mm electrodes in a row, with 10 mm of exposed insulating backing between adjacent pad edges. A break-before-make switch matrix connects any two pads to the waveform generator and leaves the other pads electrically floating. The remote selects the active pair, giving center-to-center spacings of 30, 60, or 90 mm along the row. The generator disables its output during switching and checks contact impedance before restarting the waveform.
An instrumented rehabilitation treadmill measures vertical force under each foot while a foot sleeve holds two electrodes separated by an insulating textile panel. The treadmill controller identifies lift-off when the measured force on that side falls below a configured threshold and transmits a start command to the sleeve-mounted stimulator. A rise above the threshold at the next foot contact triggers a stop command. The stimulator ends each pulse train when it receives the stop command or reaches its local duration limit.
A foot sleeve holds two skin-contact electrodes in separate insulating pockets, and its stimulation unit includes a current sensor and a differential voltage measurement circuit. After the remote starts a session, the unit inserts a low-amplitude test pulse between pulse trains and estimates contact impedance from measured voltage and current. A local controller adjusts output voltage within a preset limit to maintain the commanded pulse current. The unit suspends stimulation when measured impedance falls outside the configured contact range.
A thin pressure-sensor sheet sits below the insulating backing of a foot wrap, with separate sensing zones beneath the heel, arch, and forefoot. Four skin-contact electrodes sit on the upper face of the backing in electrically separated pockets, and a switching circuit connects one pair at a time to the waveform generator. The remote enables automatic selection, and the local controller chooses a pair from a stored mapping of plantar pressure distributions to electrode pairs. The controller changes pairs between pulse trains after the measured pressure distribution remains stable for a configured dwell time.
A conductive pad in the insole contacts the sole, and a flexible lead connects the adhesive pad above the ankle to the second output terminal. The stimulator drives current between the pads through tissue in the foot and lower leg.
Two conductive pads sit flush with the platform surface, with an insulating gap between them. A heel stop aligns the foot so its weight presses the sole against both pads.
A microcontroller times two pulse phases, and a switching bridge reverses current direction between phases. A feedback amplifier measures voltage across a shunt resistor and regulates current during each phase.
Two carbon-filled silicone pads sit flush with the upper surface of a molded insulating silicone insole. Insulating silicone fills the gap between the pads, and separate embedded traces connect them to output terminals at the heel.
A molded heel cup seats the rear of the foot and aligns the sole with the contact pads. An adjustable ankle strap holds the wearable structure against the foot during stimulation.
A handheld controller sends digital packets over a short-range radio link with a start or stop command and an amplitude setting. A receiver in the stimulation unit passes packets with a valid checksum to the microcontroller, which applies the command to the output driver.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Stimulator 4 generates programmable electrical stimulation, e.g., a current or voltage waveform or current or voltage pulses, and delivers the stimulation via an implantable medical lead 10 carrying an array of implantable stimulation electrodes 11.B · US 8,560,080 B2 · ¶ 44
The floating gate electrode 3a and control gate electrode 6a are electrically isolated due to the presence of the interelectrode insulating films 4a, 5a.A · US 2011/0001180 A1 · ¶ 35
One example method includes receiving, via a programmer for an electrical stimulator, user input indicating a target stimulation zone, and controlling the electrical stimulator to transition electrical stimulation from an initial stimulation zone to the target stimulation zone via one or more intermediate stimulation zones.B · US 8,560,080 B2 · abstract
Processor 50 may also control stimulation generator 60 to selectively deliver the stimulation via subsets of electrodes 48, also referred to as electrode combinations, and with polarities specified by one or more programs.B · US 8,560,080 B2 · ¶ 75
An empty cell means only that no passage was reproduced there.
An increase in the electric field applied to the interelectrode insulating film on the upper end portion of the floating gate electrode leads to a factor that limits the film thickness of the interelectrode insulating film and degrades the performance of the memory cell.A · US 2011/0001180 A1 · ¶ 7
It is extremely difficult to produce the above shape since the manufacturing process would be highly complex.A · US 2011/0001180 A1 · ¶ 9
The programming techniques may include controlling a transition from an initial stimulation location or initial stimulation shape (referred to collectively throughout as an “initial stimulation zone”) to a user-specified target stimulation location or target stimulation shape (referred to collectively throughout as a “target stimulation zone”) in order to limit the rate of change of stimulation.B · US 8,560,080 B2 · ¶ 6
The rate of change may be predetermined or user determined.B · US 8,560,080 B2 · ¶ 6
patent.fyi, US 2026/0355503 A1, claim 1, first published 2026-11-19T12:21:55-05:00, https://patent.fyi/US20260355503/, SHA-256 bd6cc3c780ecdaf9811b029d5e08d4e73f14d53b80e7b93efd792e6428ef0a71