1.1Fixed session at power on
The switch connects the battery to a pulse generator and a hardware countdown timer. Fixed circuit components set the pulse rate and width, and the timer disconnects the electrode output when the session ends.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The switch connects the battery to a pulse generator and a hardware countdown timer. Fixed circuit components set the pulse rate and width, and the timer disconnects the electrode output when the session ends.
A clock advances an address counter through read-only memory, and each entry supplies timing and amplitude values to a current driver. A separate logger records symptom scores and timestamps in writable memory.
A flexible resistive heater transfers heat through a fabric cover. A thermistor measures pad temperature, and a feedback controller switches heater power to maintain the setpoint.
An elastic strap loads a contoured foam pad against the abdomen. A sliding buckle sets strap tension, and the pad distributes the load across its contact surface.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A belt carries a pair of skin electrodes on each hip and an isolated two-channel pulse generator. A handheld route terminal sends left and right turn events to a belt controller over a short-range radio link. The controller maps each event to a stored profile that selects the corresponding hip and specifies the pulse timing, then triggers one charge-balanced burst at the wearer’s calibrated sensory level.
A rotary encoder, a start button, and a small display connect directly to the stimulator microcontroller. The encoder selects an electrode zone and an intensity setting, and the display shows both values. On a start command, the microcontroller maps the settings to a stored profile and drives the selected electrode pair through a current-regulated output stage.
A flexible pad carries four independent electrode pairs connected to an isolated current source through a break-before-make switch matrix. A four-bit zone mask and four stored amplitude settings define the active channels and their respective pulse amplitudes. The controller assigns the four zones successive 5-millisecond slots in a repeating 20-millisecond frame and delivers one complete charge-balanced pulse per enabled slot, giving each enabled zone a rate of 50 pulses per second.
A stationary rehabilitation cycle supplies crank angle and cadence from its shaft encoder to a stimulation controller. Surface electrode pairs over the left and right quadriceps connect to separate channels of an isolated pulse generator. The controller uses the encoder values to determine each leg’s extension window and starts the corresponding stored pulse train at the beginning of that window. A stop signal from the cycle disables both stimulation outputs.
A surface electromyography sensor on the anterior deltoid measures muscle activity, and a separate stimulation electrode pair sits over the wrist extensors. The controller computes a moving root-mean-square value and selects a stored wrist-extension profile when the value stays above a calibrated threshold for a preset interval. It delivers one burst at the programmed intensity and suspends electromyography processing during the burst and a short recovery interval. A fresh threshold crossing is required before the controller triggers another burst.
Each electrode pair connects to a switching circuit that routes it between a contact measurement circuit and an isolated stimulation output. Before each burst, the controller applies a low-amplitude alternating test current and estimates the pair impedance from the measured voltage. It intersects the requested zone mask with the set of pairs whose impedance falls within the configured contact limits, then delivers the programmed burst through the resulting active pairs. If the active mask is empty, the controller holds the output off and displays a contact prompt.
A voice-coil actuator moves a flexible pad held against the lower abdomen by an elastic band. A motor driver controls vibration amplitude, burst duration, and pauses between bursts.
A real-time clock drives the output gate through a relay with its own timing circuit. After the relay closes, the pulse controller sets amplitude and width from stored values.
A touchscreen form collects a symptom score on a zero-to-ten scale and a preferred starting intensity. The device controller receives both values in a timestamped message over a short-range radio link.
A controller uses the reported symptom score to select a row in a stored table. It combines the selected pulse rate and session duration with the entered starting intensity, bounded by the device's configured output limit.
The controller receives the intensity at which the user first reports a sensation and the highest intensity the user reports as comfortable. It sets a session starting amplitude from the first value and calculates a stepped ramp capped at the second.
A microcontroller enables a constant-current driver connected to a pair of hydrogel electrodes. A polarity switch produces biphasic pulses, and a hardware timer applies the pulse width and repetition interval specified by the stimulation profile.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Clinician programmer 46 supports telemetry (e.g., radio frequency telemetry) with implantable pulse generator 12 to download neurostimulation parameters and, optionally, upload operational or physiological data stored by implantable pulse generator 12.B · US 2022/0339442 A1 · ¶ 42
These counters 118 may be used in determining which pulses or stimulation sets to skip or when to stop repeating a stimulation set.A · US 8,433,416 B2 · ¶ 54
Microprocessor 74 may uses these stimulation settings and parameters in configuring switch matrix 90, manipulating pulse amplitude and pulse width control 88, and producing stimulation pulses.A · US 8,433,416 B2 · ¶ 63
The operation may also include generating, by the IPG, electrical pulses for the stimulation program according to the one or more parameters, and generating, by the IPG, pinging-pulses at amplitudes greater than pulse amplitudes of the therapeutic pulses of the stimulation program.B · US 2022/0339442 A1 · ¶ 82
An empty cell means only that no passage was reproduced there.
More specifically, this invention relates to a method for creating complex stimulation patterns with a stimulation device coupled to one or more leads with one or more electrodes.A · US 8,433,416 B2 · ¶ 2
Electrical energy, similar to that used to inhibit pain perception, may also be used to manage the symptoms of various motor disorders, for example, tremor, dystonia, spacticity, and the like.A · US 8,433,416 B2 · ¶ 5
Although the paresthesia can be uncomfortable or even painful in patients, the paresthesia is often substantially more tolerable than the pain otherwise experienced by the patients.B · US 2022/0339442 A1 · ¶ 6
It has been found that such burst stimulation suppresses neuropathic pain at least as well as, and possibly better than, traditional tonic SCS stimulation and provides such pain relief without eliciting paresthesia.B · US 2022/0339442 A1 · ¶ 8
patent.fyi, US 2026/0355512 A1, claim 1, first published 2026-11-19T12:21:55-05:00, https://patent.fyi/US20260355512/, SHA-256 cd38f84f326ef46268010303bb186b139eaf237f819bb1522fcad724afa13fdd