1.1Sintered ceramic grain network
Barium titanate nanopowder is pressed and fired to form a dense ceramic with bonded grains. Electrodes apply a poling field and then collect the alternating charge generated by acoustic stress.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Barium titanate nanopowder is pressed and fired to form a dense ceramic with bonded grains. Electrodes apply a poling field and then collect the alternating charge generated by acoustic stress.
A film of poly(vinylidene fluoride-co-trifluoroethylene) is annealed and poled through its thickness to align ferroelectric domains. Thin electrodes on opposite faces collect the alternating charge as ultrasound strains the film.
Inner and outer electrodes establish a radial poling field across the ceramic shell. Incident ultrasound excites elastic motion of the shell, and a rectifier connected across the electrodes supplies a storage capacitor.
A radially poled ceramic ring carries a common inner electrode and four electrically isolated outer electrode sectors. Each sector feeds a separate rectifier so that outputs with different phases can charge the same capacitor.
Electrodes cover the two broad faces of a plate poled through its thickness. The plate thickness is approximately half the longitudinal acoustic wavelength in the solid at the drive frequency, and a rectifier converts the resulting alternating voltage to direct current.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A regular polyhedron molded from a polymer containing metal oxide nanoparticles carries electrode pairs on oppositely poled face regions. Each pair feeds a separate rectifier, and the rectifier outputs charge a common capacitor that powers a temperature sensor inside a liquid storage tank. A transducer bonded to the outer tank wall sends ultrasound through the wall and liquid, and a waterproof coating electrically isolates the receiver from the liquid.
Sodium niobate nanoparticles replace the metal oxide filler in a printable composite made with a curable epoxy resin. The composite is deposited into a regular polyhedral mold and cured, and conductive coatings are applied to an opposing pair of faces. A direct electric field between the coatings poles the composite, and the same coatings collect alternating charge under ultrasonic compression.
A regular polyhedron of polymer and metal oxide nanoparticles has two opposing faces spaced 2.0 mm apart and coated with electrodes. For a cured composite with a measured longitudinal sound speed of 2,400 m/s, a half-wavelength estimate gives a starting drive frequency of 600 kHz. The transmitter sweeps from 450 to 750 kHz in 5 kHz steps, and the drive frequency is set to the step that supplies the highest rectified power to a fixed load in the coupling medium.
A regular polyhedral receiver made from a polymer and metal oxide nanoparticles sits beside a capacitive pressure sensor in a sealed implant package. The receiver electrodes connect through a rectifier to a storage capacitor, and a voltage supervisor enables the sensor electronics once the capacitor reaches the operating threshold. A flexible diaphragm transfers external pressure to the sensor, and a load switch modulates the receiver impedance so an external ultrasonic reader can recover the pressure reading from the echo.
A regular polyhedron made from a polymer and metal oxide nanoparticles connects through face electrodes and a rectifier to a low-current battery charger. The charger supplies a rechargeable solid-state microbattery, and a regulator draws power from the battery to operate a miniature sensor between ultrasound bursts. A capacitor at the rectifier output buffers the incoming energy, and a voltage supervisor enables the charger when the capacitor reaches the charger input threshold.
An external ultrasonic array powers a regular polyhedral receiver made from a polymer and metal oxide nanoparticles. An implant circuit measures rectified receiver voltage and reports it by switching an electrical load across the receiver electrodes to modulate the returning echo. The array controller tests a preset set of transmit delay patterns at a fixed drive level, selects the pattern that yields the highest reported voltage, and repeats the sweep when the voltage drops below a set threshold.
Barium titanate particles with a nominal diameter of 100 nanometers are dispersed at 15 percent by volume in poly(vinylidene fluoride-co-trifluoroethylene). The composite is cast, dried and poled between electrodes on opposite faces.
A piezoelectric cube carries an electrode on each of its six square faces, with insulating gaps along the edges. One opposing pair applies the poling field and then connects to a rectifier for charge collection.
A piezoelectric body is molded as a regular octahedron with eight congruent equilateral triangular faces. Metal films on two opposite parallel faces serve as electrodes for poling and for collecting charge generated by acoustic stress.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A ceramic-polymer film includes a polymer matrix; a plasticizer; a lithium salt; and AlxLi7-xLa3Zr1.75Ta0.25O12 where x ranges from 0.01 to 1 (LLZO), wherein the LLZO are nanoparticles with diameters that range from 20 to 2000 nm and wherein the film has an ionic conductivity of greater than 1×10−3 S/cm at room temperature.B · US 2020/0335814 A1 · abstract
Building blocks may be shaped as platonic solids.A · US 2015/0079870 A1 · ¶ 8
An empty cell means only that no passage was reproduced there.
Groups of building blocks may be used as an educational toy by children, or may be used by adults or children to explore various three-dimensional shapes.A · US 2015/0079870 A1 · ¶ 2
All-Shape building blocks may be combined to form or give the appearance of various geometric structures, and the included magnetic materials may be used to retain the formed geometric structure shape.A · US 2015/0079870 A1 · ¶ 8
There are two critical challenges to achieving high performance batteries using solid electrolytes: (1) low ionic conductivities of many solid electrolytes, and (2) large resistance posed by the electrode-electrolyte interface.B · US 2020/0335814 A1 · ¶ 4
The present invention generally relates to electrochemical devices and, more particularly, to a method of fabricating polymeric electrolytes having superior ionic conductivity and mechanic properties for electrochemical cells and batteries.B · US 2020/0335814 A1 · ¶ 2
patent.fyi, US 2026/0355525 A1, claim 1, first published 2026-11-19T12:45:34-05:00, https://patent.fyi/US20260355525/, SHA-256 1929194e1ee4358156ecd2d2a1711e647b1803856a8daa6e8b21d35415f314f7