1.1Flat face with stencil
A stencil seats against the flat housing face and exposes the insert and the annular filler joint. A squeegee spreads thixotropic sealant through the opening, and the stencil lifts away before the coating cures.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A stencil seats against the flat housing face and exposes the insert and the annular filler joint. A squeegee spreads thixotropic sealant through the opening, and the stencil lifts away before the coating cures.
The ramp meets the top of the annular joint at its lower edge. A dispensing needle lays a continuous bead on the ramp, and the liquid sealant flows down to wet the filler before curing.
A ceramic body forms a continuous sidewall and end wall during firing. Metallized vias pass through the end wall, and a brazed metal ring at the open end joins the body to a metal lid.
A screen printer deposits platinum paste in parallel strips on an unfired alumina sheet. A second sheet covers the strips, and lamination and firing consolidate the ceramic around the traces while leaving terminal pads accessible at opposite ends.
A glass preform fits into the annular gap around the ceramic insert. During firing, the glass softens and wets the ceramic and the prepared housing surface, then solidifies into a continuous seal on cooling.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A stepped housing fits into the wall of a sealed seawater pressure logger and carries two pins through a solid insulating insert. A metal filler joins the insert perimeter to the cavity wall, and a corrosion-resistant sealant fills part of the seawater-facing well and covers the insert face and exposed filler. The pins connect an external pressure transducer to the recording circuit inside the dry enclosure.
A dense zirconia insert sits in the stepped housing, and glass seals hold conductive pins in the insert apertures. A silver-copper-titanium active braze replaces the peripheral metal filler and wets the zirconia and housing wall during vacuum brazing. After cooling, a corrosion-resistant sealant fills part of the well and covers the insert face and exposed braze.
A 9 mm diameter insulating insert carries eight 0.35 mm pins at 45 degree intervals on a 6 mm pitch circle. A metal filler occupies the 0.10 mm radial gap between the insert and the cavity wall. The insert face and exposed filler sit flush with the ridge, and the lip rises 0.60 mm above it. A 0.25 mm sealant layer covers the insert face and filler while leaving the pin tips exposed for connection.
The stepped housing fits into the wall of an implant enclosure, and sealant in the outward-facing well covers the insert face and peripheral filler. On the dry side, each pin passes through a plated hole in a printed circuit board mounted parallel to the insert. A shunt capacitor connects each signal pin to a ground plane bonded to the housing, diverting high-frequency interference before it reaches the sensing circuit.
A stepped housing with a solid insert, conductive pins, and a perimeter metal filler mounts beside a separate optical fiber feedthrough in a sealed sensor module. Sealant in the electrical feedthrough well covers the insert face and exposed filler while leaving the pin ends accessible. The pins carry power and electrical readout signals, while the separate fiber carries illumination to the sensing head and returns reflected light to an internal photodetector.
An overhead camera locates the raised lip and pin centers on the assembled feedthrough, and a displacement sensor measures the ridge and insert heights. A controller uses these measurements to set the nozzle height and trace a dispensing path over the peripheral metal filler and between the pins. A laser line profiler measures the cured surface, and the controller flags assemblies with coating thickness outside the programmed limits.
A machined titanium housing has a horizontal annular ridge and a raised lip with a 45-degree inner chamfer. The chamfer narrows toward the ridge and guides dispensed sealant into the well.
A dense alumina disk seats concentrically in the housing cavity. Its ground outer diameter sets a uniform annular clearance for the filler, and fired apertures locate the conductors.
Platinum-iridium pins run through individual cylindrical bores in an alumina insert. An annular glass seal holds each pin in its bore, and the ends project from both faces for electrical termination.
A dispensing needle lays low-viscosity epoxy over the exposed filler and across the insert top between the pins. The epoxy cures inside the raised lip with the pin tips exposed for electrical connection.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
For example, ferrule 72 may include a cylindrical annulus having a radially exterior surface, a radially interior surface, and an interior annular surface that is disposed within enclosure 58.B · US 2020/0360702 A1 · ¶ 37
An insulator 74 may be coupled to the radially interior surface of ferrule 72. In some examples, insulator 74 may include a cylindrical annulus having a radially exterior surface, a radially interior surface, and an interior annular surface that is disposed within enclosure 58.B · US 2020/0360702 A1 · ¶ 38
The feedthrough includes a ferrule extending through the feedthrough aperture and coupled to the enclosure, an insulator extending through the ferrule to the exterior of the battery, and a pin extends through the insulator from the interior of the battery to the exterior of the battery, the insulator electrically insulating the pin from the ferrule.B · US 2020/0360702 A1 · ¶ 7
A method for manufacturing a brazed part is disclosed that includes coating a substrate surface to be joined by first cold spraying a braze filler metal powder upon the surface to clean the surface followed by further spray the powder to form a coating layer of a braze alloy upon the surface. The coated surface is assembled with another surface to be joined and brazed together to form the brazed part.A · US 2008/0160332 A1 · abstract
An empty cell means only that no passage was reproduced there.
Therefore, what is needed is a process for preparing surfaces for brazing that does not suffer from the disadvantages of the existing surface preparation processes.A · US 2008/0160332 A1 · ¶ 5
Accordingly, it is an object of the present invention to use high velocity cold spraying to coat a braze alloy upon a substrate surface and then braze that surface to at least one other surface to form a brazed part.A · US 2008/0160332 A1 · ¶ 6
The shape of the feedthrough insulator cap prior to reflow provides coverage of the ferrule and pin to reduce occurrence of electrical shorting due to, for example, lithium ion dendrite growth.B · US 2020/0360702 A1 · ¶ 4
Thus, the feedthrough insulator cap may increase the useable life of the battery.B · US 2020/0360702 A1 · ¶ 4
patent.fyi, US 2026/0355528 A1, claim 1, first published 2026-11-19T12:45:34-05:00, https://patent.fyi/US20260355528/, SHA-256 4a546aaa087c69de73fd8befa2556607e0981b38ee81c0bb70cf83990803c5c9