1.1Violet light source
A violet light-emitting diode feeds a disperser and an ear-canal light guide. A constant-current driver sets the optical output, and a timer sets the illumination interval.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A violet light-emitting diode feeds a disperser and an ear-canal light guide. A constant-current driver sets the optical output, and a timer sets the illumination interval.
The lamp remains energized throughout the wear interval. A solenoid opens an opaque shutter between the lamp and the disperser for each timed exposure.
A padded ear cup holds the guide and a fused-silica projection lens outside the canal opening. The lens directs a diverging UVB beam through the opening to illuminate the entrance and adjacent canal wall.
A soft earpiece supports the guide, and an outer housing supports the disperser. A locating shoulder aligns the polished guide entrance with the disperser across a 0.5 mm air gap.
Laser-etched patches along a fused-silica rod scatter guided UVB toward the canal wall. Patch density increases along the rod so that the side surface extracts most of the guided power before it reaches the tip.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A switchable UVB emitter feeds an annular disperser at the entrance to a blind bore in a machined part. A fused silica rod fixed to the disperser carries light into the bore, and shallow etched bands direct it onto the sidewall. A black ceramic cap fixed to the rod tip blocks forward illumination of the bore floor. A filtered camera at the bore entrance records visible fluorescence from a UVB-excitable inspection coating.
A synthetic sapphire rod replaces the elongate guide member and fits into the outer ear canal. Its polished proximal face seats against the light disperser, and a keyed collar fixes the rod in alignment with the disperser. A ground band along the rod scatters guided UVB through the side surface. An opaque ceramic cap bonded over the distal face intercepts light that reaches the tip.
A cerium-doped glass disk replaces the distal optical stop on a fused silica guide. The disk covers the entire polished distal face and is held against it by a recessed ceramic collar fixed to the guide. The disk thickness is selected from measured transmission data for the emitter band, and a ceramic backing intercepts light transmitted through the disk. The disperser feeds the guide at the proximal end, and textured side surfaces scatter UVB outward before it reaches the cap.
Three earpiece assemblies use guide rods of 6, 9 and 12 mm measured from the disperser face to the distal cap. Each rod has a diameter of 2.5 mm and carries a 1 mm wide frosted band centered halfway along its length. The rods share the same proximal mounting geometry and use opaque caps that cover the full distal face. A UVB detector on a translation stage measures the axial emission profile of each assembly in a mock ear canal.
A video otoscope speculum carries a slender UVB guide in an offset channel beside the camera's viewing axis. A disperser at the base couples a switchable UVB emitter to the guide, while a fixed opaque cap blocks forward emission at the guide tip. The camera views past the cap through a separate clear window under visible illumination. A mode selector alternates between visible imaging and UVB delivery.
A UVB photodiode samples light through a side port in the disperser that feeds the canal guide. The guide emits through its textured side surface, and an opaque distal stop blocks direct forward output. A controller uses a stored calibration to convert the photodiode current to an estimate of guide output power and adjusts the emitter current to hold a setpoint. The controller integrates the estimated power over time and switches off the emitter when the accumulated optical energy reaches the programmed value.
A UVB light-emitting diode faces the polished entrance across a short air gap inside an opaque alignment sleeve. Surface texture along the guide redirects the coupled light toward the canal wall.
A light-emitting diode with a 310 nm peak emission mounts on a ceramic carrier. A constant-current driver energizes the diode for a programmed interval.
A fused-silica disk receives UVB from a diode on its polished face. An etched exit face spreads the transmitted light over a range of angles into the guide entrance.
A 3 mm diameter fused-silica rod forms the elongate member, and an annular collar fixes its proximal end to the disperser. Fine surface texture along the inserted length scatters UVB toward the canal wall.
A closed-end titanium cap crimps onto a circumferential groove near the distal tip of the guide. The solid end wall blocks UVB traveling longitudinally through the guide.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
This invention is a transparent or translucent light spreader, enabling a single, higher powered LED light source to spread its light throughout the length of the light spreader.A · US 7,172,323 B1 · ¶ 5
One or more secondary ultraviolet B (UVB) emitters are mounted to the body to also illuminate the growing area. The emission of the primary luminaires and secondary emitters is controllable to provide the desired light fixture emission to the growing area.B · US 2020/0053967 A1 · ¶ 10
In order to spread the light being emitted from an LED, an LED light spreader has a light conductive end, an optical path conversion side, and a light transmitting side.A · US 7,172,323 B1 · abstract
The UVB emitters can have a lens to help disperse light in the desired emission pattern.B · US 2020/0053967 A1 · ¶ 40
The light spreader set forth in detail herein is comprised of a series of sections, wherein each section has a partial cylindrical length and a length having a curved prism or partial frustoconical length, both forming an elongated member having a light emitting or transmissible side and a rounded surface or optical path conversion side.A · US 7,172,323 B1 · ¶ 8
An empty cell means only that no passage was reproduced there.
Among the problems associated with the prior art includes low luminosity of the LEDs, installation, maintenance, and changing of a plurality of LEDs.A · US 7,172,323 B1 · ¶ 4
The instant invention enables a single LED to simulate the effect of having several discrete LEDs on a circuit board.A · US 7,172,323 B1 · ¶ 9
LEDs by contrast, can emit the same luminous flux as incandescent and fluorescent lights using a fraction of the energy.B · US 2020/0053967 A1 · ¶ 6
One drawback is that LEDs typically emit in narrow emission spectrum and can often not be as effective as sunlight in enhancing plant growth.B · US 2020/0053967 A1 · ¶ 8
patent.fyi, US 2026/0355531 A1, claim 1, first published 2026-11-19T12:45:34-05:00, https://patent.fyi/US20260355531/, SHA-256 ac72455b3740161f420a69aa6a3a28a1e90afb83c48f357b508a4f6e53bb2738