1.1One piece structural shell
Integral bearing seats in the aluminum shell support the exercise pivot. Thickened mounting pads secure the resistance unit and transfer its reaction load through the shell to the floor.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Integral bearing seats in the aluminum shell support the exercise pivot. Thickened mounting pads secure the resistance unit and transfer its reaction load through the shell to the floor.
A link from the handle drives a horizontal rack that turns a circular pinion keyed to a second pinion on the same shaft. The second pinion raises a vertical rack carrying a counterweight, and the ratio of the two pitch radii sets the force ratio between the racks.
The sector contains three selectable cable attachment positions. Mechanical stops limit cam rotation so the tensioned cable runs within the grooved sector throughout the exercise stroke at each setting.
An offset guide sheave directs the cable toward a swaged eye pinned to one of three clevises on the cam face. The selected clevis sets the cable attachment angle, and the cable spans directly from the sheave to the eye throughout the stroke.
A captive pin holds the terminal at a single location in the groove. With the weight stack resting on its stops, an inline turnbuckle changes the effective cable length and shifts the handle angle at which the cable starts to lift the stack.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A pivoting guide gate on a packaging conveyor shares a shaft with a cam that has a full peripheral groove and a series of cross holes. A cable runs from an extension spring through a fixed guide sheave to a hollow end fitting seated in the groove and held by a removable cross pin. Passing packages swing the gate open and stretch the spring, which returns the gate after each package clears. Moving the fitting to a different cross hole changes the spring preload at the closed stop.
A curved T-slot replaces the groove with cross holes, and a sliding T-nut and cable clamp replace the hollow fitting and removable pin. Two arcuate retaining strips bolt to the cam faces and form the narrow mouth of the slot, with an assembly opening covered by a removable plate. A clamp screw draws the T-nut against the inner shoulders of the slot and clamps the cable fitting against the outer faces of the retaining strips. With the cable slack, loosening the screw lets the fitting and nut slide together to a different position.
An oil-filled rotary damper and a clock spring drive a cable drum mounted on a shaft supported by the exercise frame. The cable runs from the drum through a fixed guide sheave to a hollow fitting pinned in the cam groove. A one-way clutch couples the drum to the damper during cable payout, and the clock spring rewinds the drum during the return stroke. A damper adjustment sets resistance during payout, and the selected fitting position sets the drum angle and spring preload at the starting stop.
A seated ankle exercise machine uses a footplate fixed to the shaft of a 160 mm diameter circular cam. The cam has a full peripheral groove and 24 cross holes at 15-degree intervals, and the hollow cable fitting uses a 6 mm removable pin. Stops limit footplate travel to 35 degrees, which takes up about 49 mm of cable at an effective radius of 80 mm. Moving the unloaded fitting one hole changes the cable take-up at the starting stop by about 21 mm over the range where the cable stays wrapped in the groove.
A cable runs from the pinned fitting in the cam groove over fixed frame pulleys to the lifting rod of a selectorized weight stack. A pivoting exercise arm shares the cam shaft and winds cable into the groove as the arm moves through the lifting stroke. A threaded take-up at the lifting rod sets cable slack with the arm against its starting stop and the plates resting on the stack base. Shifting the cam fitting changes the point in the arm stroke where the selected plates begin to rise.
A rotary encoder measures cam angle, and a tension sensor in the cable path measures cable force. A sensor beside the cam reads a coded magnetic marker on the removable fitting when the exercise arm rests at its starting stop. A controller stores the cam's effective cable moment arm at each angle for each attachment position and multiplies that moment arm by measured tension to estimate torque during a calibration stroke. The controller compares the measured torque curve with a stored target and displays the cross hole selected for the next calibration stroke.
A welded steel base ties two rectangular tube uprights together. A crossmember supports the exercise lever bearings, and welded gussets stiffen the upright joints under cable tension.
A machined aluminum disk carries a rounded cable groove that follows the entire outer edge. Two sealed ball bearings support the disk on a frame-mounted shaft, and a keyed hub transmits rotation from the exercise lever.
A tubular exercise arm bolts to a flanged hub keyed to the cam shaft. Pushing or pulling the arm rotates the cam in the corresponding direction, and two adjustable stops set the travel limits.
A swaged cable shank joins a hollow steel barrel that seats in the groove. A captive pull pin passes through the cam cheeks and the barrel bore to retain the terminal at the selected position.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The exercise frame 201 may include additional support members such as bars in order to provide support and to provide additional exercise opportunities such as chin-ups etc.B · US 2011/0306479 A1 · ¶ 40
As the said cylindrical grooved cam rotates, the lenses, which are assembled in a lens barrel and set in the cylindrical grooved cam engaging with the grooved cams through driving pin or raised portion of the lens barrel rim, are moved back and forth for focusing or moved to control the zooming according to the zooming data that are interpreted as cam data and transferred to grooved cams.A · US 6,937,403 B2 · ¶ 4
An empty cell means only that no passage was reproduced there.
The invention relates to a cylindrical grooved cam made of plastic, on the inner cylindrical surface of which the grooved cams to control lens driving such as lens zooming or lens focusing of optical equipments like cameras are provided.A · US 6,937,403 B2 · ¶ 2
The mold with the split-core slide is very complicatedly designed, and the cost of the mold is extremely expensive.A · US 6,937,403 B2 · ¶ 5
The present invention relates to an exercise device and more particularly to an exercise device that provides resistance to the legs, abdominal, chest, back, shoulder, arm and hand.B · US 2011/0306479 A1 · ¶ 1
Despite the great variety of exercising and rehabilitative devices available there remains a need for a device capable of providing users with a means of strengthening the muscles, ligaments and tendons of an injured wrist, hand or forearm with the support of the healthy wrist, hand or forearm, while simultaneously improving the full range of motion.B · US 2011/0306479 A1 · ¶ 3
patent.fyi, US 2026/0355560 A1, claim 1, first published 2026-11-19T12:45:34-05:00, https://patent.fyi/US20260355560/, SHA-256 d0823c2c72b74ffa72a2f6cd2dc6dbc62850a85dc07c863efe1799385f8dda52