1.1Floor support on a plate
The base frame bolts to the center of a wide steel plate with rubber pads beneath both ends. The rear curved tubes bolt to gusseted brackets at the ends of the plate.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The base frame bolts to the center of a wide steel plate with rubber pads beneath both ends. The rear curved tubes bolt to gusseted brackets at the ends of the plate.
Matching grooves in the primary and secondary pulleys engage the belt teeth, and the pulley tooth counts set the speed ratio. An adjustable idler sets the belt tension, and a separate output sheave on the secondary shaft drives the second stage.
The second-stage belt turns a flywheel whose shaft runs in bearings on the base frame. A threaded knob compresses a spring against a friction pad, and the pad bears on the flywheel rim to set the braking torque.
Bearings in the upright support the two parallel shafts, each fitted with a spur gear of the same tooth count. An idler gear meshes with both gears so that the crank and pulley shafts turn at the same speed and in the same direction.
Two straight rectangular steel tubes project from brackets at the top of the upright. An offset clevis at each free end places the upper mounting pin in line with the corresponding lower mount.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A fixed training station uses the vertical tube, paired pedal arms, reciprocating handles, and belt-driven magnetic flywheel to simulate repeated ladder climbs indoors. Anchor plates welded to the ground-contact tube and rear of the base frame bolt to the training floor. Replaceable pedal plates carry raised transverse ribs that provide boot contact surfaces, while the paired crank arms keep the left and right stepping motions half a cycle apart.
Toothed synchronous belts and matching pulleys replace the V-belts and grooved pulleys in both transmission stages. A large toothed pulley on the crankshaft drives a smaller pulley on the intermediate shaft, and a second large pulley on that shaft drives a smaller pulley on the flywheel shaft. Slotted bearing mounts on the intermediate shaft set first-stage belt tension, and a slotted flywheel mount sets second-stage belt tension after the intermediate shaft is secured.
Each handle mounts on the moving upright of a four-bar parallelogram with two equal-length swing links. The swing links pivot on a rigid bracket between the front and rear curved tubes, with equal vertical spacing between the pivots on the bracket and on the moving upright. A pinned pushrod connects the lower swing link to the horizontal pedal arm so pedal motion raises and lowers the handle along a shallow arc while it remains upright.
Each crank plate has three threaded holes on a common radial line at 40, 60, and 80 mm from the shaft center. With the drive stationary, the two removable shoulder bolts that serve as crank pins move to matching holes on opposite sides of the shaft, preserving the 180-degree phase offset. The pin settings produce circular travel diameters of 80, 120, and 160 mm at the crank joints, while the pedal linkages constrain the resulting foot paths using the same base pivots.
A freestanding body-weight support gantry straddles the machine, with its overhead pulley centered above the midpoint of the pedal working area. A low-stretch cable passes over the pulley from a torso and thigh harness to a counterweight stack that travels on guide rods behind the machine. Adding mass to the stack increases upward harness tension and reduces the user's weight carried by the pedals while the belt transmission and magnetic flywheel supply motion resistance.
A toothed target wheel on the crankshaft passes a fixed Hall-effect gear tooth sensor that supplies pulses to a controller. A lead screw actuator moves the permanent magnet carrier toward or away from the conductive flywheel rim, and a position sensor reports the carrier position. Once per second, the controller compares measured cadence with a selected target and moves the carrier toward the rim when cadence exceeds the target band or away when cadence falls below it. Travel switches bound actuator motion, and a stopped crank triggers a return to the widest magnet gap.
Each cantilever tube linkage ends in a steel eye fitted with two flanged bronze bushings. A hardened pin passes through the bushings and an upright-mounted clevis, allowing the linkage to swing in its operating plane.
Each horizontal arm uses rectangular steel tubing with welded cross sleeves at the crank, cantilever tube and pedal linkage pivots. The sleeves support the pivot pins across both walls of the tube.
A formed steel pedal pan bolts to a mounting plate at the end of each horizontal arm. A molded rubber insert with transverse ribs forms the foot-contact surface, and a raised perimeter lip limits sideways foot movement.
A steel link has a spherical plain bearing in a pressed-in housing at each end. Shoulder bolts connect the bearings to clevises on the horizontal arm and base frame, allowing the link to pivot and accommodate small alignment errors.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Functional parts of a drive unit for parking brakes in vehicles as shown in FIG. 1 comprise a brushless direct current motor 10 with an external rotor, a reduction gear configured as a two-stage belt drive whose first stage consists of a pinion 12 connected to the external rotor of the direct current motor, a belt pulley 14 and a toothed belt 16, and whose second stage consists of a pinion shaft 18 connected to the belt pulley 14, a drum 20 and two parallel toothed belts 22,A · US 6,837,357 B2 · ¶ 11
After the large revolver wheel 2 is set, the magnetic resistance flywheel 7 is place on the brace 12 which is on the same side with the belt disc 3, The magnetic resistance flywheel 7 will uses a belt 71 to connect with the belt disc 3, so as to revolve the magnetic resistance flywheel 7 through the rotation of the large revolver wheel 2.B · US 2005/0009672 A1 · ¶ 14
An empty cell means only that no passage was reproduced there.
The invention provides a compact drive unit for actuating parking brakes which functions especially quietly with a high efficiency and which carries out the actuation procedure within a very short period of time.A · US 6,837,357 B2 · ¶ 4
Since the two-stage belt drive is reversible, i.e. it allows a reverse rotation, there is a need for a latching mechanism that maintains the activation state of the parking brake when the drive motor is switched off.A · US 6,837,357 B2 · ¶ 5
Such a spring, however, loses its flexibility after a while, making it unable to reposition the pulling rope back to the original place.B · US 2005/0009672 A1 · ¶ 2
The main objective for the present invention is to provide a magnetic tension control weight training machine with a precise control over the resistance force through a large revolver wheel that rotates toward a specific direction.B · US 2005/0009672 A1 · ¶ 3
patent.fyi, US 2026/0355571 A1, claim 1, first published 2026-11-19T13:13:53-05:00, https://patent.fyi/US20260355571/, SHA-256 cfbaa75520a859623c5fa8bbfddf9f14331b6ef58ba461ea93a1efaead94984f