1.3Vertical sliding handle carriages
Linear bearings guide each carriage along a pair of vertical rails. A separate cable couples each carriage to its resistance unit, and a linear encoder measures carriage travel.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Linear bearings guide each carriage along a pair of vertical rails. A separate cable couples each carriage to its resistance unit, and a linear encoder measures carriage travel.
A rotary encoder on the console changes the requested load in one-kilogram increments. A separate confirmation button sends the selected value to the controller before the lift begins.
A horizontal sleeve on each lever arm accepts calibrated steel plates, and a locking collar retains them. The selected plate mass and its distance from the pivot determine the gravitational torque at each arm angle.
Both handles attach to a common crossbar, and a load cell measures the total force transmitted from the crossbar to the resistance unit. A position encoder measures crossbar travel, and the controller derives lift velocity, power, and range of motion from the shared measurements.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A warehouse training station mounts two independently pivoting lever arms on a floor frame and spaces their handles to match the handholds on a shipping tote. A thumb switch on each handle sends a resistance request to the controller, which sets the load on the corresponding arm before the lift. Pivot encoders and load pins measure travel and force on each side, and the display reports the difference in lift onset and peak force between the hands.
A separate steel plate stack replaces the load actuator on each side, and a cable connects the stack's lifting rod to the corresponding lever arm through a fixed pulley. Each stack has a carriage that moves a locking pin into the plate selected by the load controller in response to the handle input. The controller enables the carriage only when the stack is fully seated and confirms pin engagement with a position switch before displaying the selected load.
Each lever places its handle 450 mm from the pivot, and adjustable stops limit the lever to a 12-degree sweep that gives the handle about 94 mm of arc travel. Each handle input changes the commanded handle resistance in 5 N increments over a range of 20 to 150 N per side. The load controller uses feedback from a load pin at each handle to maintain the selected force as the lever rotates.
A frame with two independently loaded lever arms stands inside a multi-camera motion capture area, with markers on each handle and on the user's ankles, knees and hips. The machine controller sends a shared timing pulse to the camera recorder and records the same pulse with its own force and lever position samples. A workstation aligns the recordings and displays knee and hip angles at the time of peak handle force on each side.
An overhead body-weight support system suspends a pelvic harness between the two independent lever arms. A load cell in the suspension line measures harness tension, and a feedback controller adjusts the vertical pull as the user rises and lowers. The machine applies the resistance selected at each handle and displays measured harness tension alongside the force and travel recorded for each arm.
Each lever pivot carries an encoder, and each handle input selects separate resistance settings for upward and downward travel on its side. The controller estimates signed handle velocity from successive encoder readings and detects a phase change when the new direction persists for 100 ms above a 20 mm/s speed threshold. Between these events the controller holds the last setting and ramps to the new setting over 250 ms after a phase change.
The base and uprights use rectangular steel tubing with a 4 mm wall thickness. Welded gussets reinforce the upright joints, and machined mounting plates locate the two pivot bearings.
Each lever arm rotates on its own steel shaft supported by two sealed rolling bearings. A clevis on each arm connects it to a separate resistance cable, so either arm travels independently.
Each handle carries a spring-centered rocker that the user operates with the thumb while maintaining a grip. One direction raises the setpoint by one kilogram per press, and the other lowers it by the same amount.
The controller samples a force transducer and a pivot encoder on each side at 200 samples per second. It converts pivot angle to handle position using the arm geometry, calculates power from tangential handle force and handle velocity, and measures reaction time from the start cue to the first crossing of a speed threshold.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Referring to FIG. 1, an exercise apparatus 100 is shown which includes a frame 102 having a base 104 configured to support the apparatus 100 on an underlying surface.A · US 2008/0242520 A1 · ¶ 21
The electronic circuit sends an electrical signal of the measurement to the LCD display.B · US 9,052,181 B1 · ¶ 7
A handle 144 may be coupled to an end of the selector pin 142 for ease of manipulation and operation by a user of the exercise apparatus 100. The selector pin 142 is configured to be displaced relative to the body 140 and the weight stack 112 in a direction that is generally transverse to the orientation of the selector rod 110.A · US 2008/0242520 A1 · ¶ 28
The inductive pick-up reads the plurality of cross filaments or wires and outputs a distance traveled by the digital readout device to the electronic circuit. The electronic circuit sends an electrical signal of the measurement to the LCD display.B · US 9,052,181 B1 · ¶ 7
An empty cell means only that no passage was reproduced there.
The use of selector pins with weight stacks of an exercise apparatus has been relatively efficient and effective in terms of enabling multiple users to use the same machine as well as enabling individual users to use a single machine for a variety of different exercises.A · US 2008/0242520 A1 · ¶ 6
In such instances, the selector pin may become disengaged during an exercise routine causing the weight plates to fall and essentially eliminating all resistance instantaneously.A · US 2008/0242520 A1 · ¶ 6
Accordingly, there is a clearly felt need in the art for a portable digital readout measuring device, which may be mounted to and removed from industrial machinery, such as milling machines, horizontal machines, bullards, vertical turret lathes, horizontal lathes and the like without the use of tools.B · US 9,052,181 B1 · ¶ 6
The present invention provides a portable digital readout measuring device, which may be mounted to and removed from industrial machinery without the use of tools.B · US 9,052,181 B1 · ¶ 7
patent.fyi, US 2026/0355578 A1, claim 1, first published 2026-11-19T13:13:53-05:00, https://patent.fyi/US20260355578/, SHA-256 ac7f94ac9d5da612302c9b4585e70f73bf3831505707115fcb8bcb7fe9352868