1.1Flexible skirt bonded to lens
A silicone skirt bonds to the perimeter of a tempered glass lens. Reinforced silicone tabs transfer strap tension to the skirt and compress its sealing lip against the face.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A silicone skirt bonds to the perimeter of a tempered glass lens. Reinforced silicone tabs transfer strap tension to the skirt and compress its sealing lip against the face.
The lower edge of the silicone skirt seats across the upper cheeks and nasal bridge. The enclosed eye chamber provides a clear view during surface swimming, and a separate nose clip closes the nostrils.
The frame seats the lens closer to the brow and cheekbones. The skirt spans the shorter distance from the lens to the face, and the lens retains clearance for blinking.
A smooth silicone bulge slopes toward a one-way valve at the bottom of the nose pocket. Exhaling through the nose raises chamber pressure and pushes collected water through the valve.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A mask for emergency escape training uses a rigid frame, a wide lens and a soft facepiece with a hollow nose housing. A single inward protrusion runs below the lens and sits forward of the rear sealing edge, with an exterior concavity opening downward into the tank. The protrusion reduces the enclosed air volume, and the downward opening lets the pocket drain when the trainee lifts the mask above the water.
An injection-molded styrenic block copolymer thermoplastic elastomer forms the rear sealing edge, hollow nose housing and recessed inward protrusion in one piece. A molded bead around the lens opening seats in a matching groove in the rigid frame and is captured by the lens retainer. A core on the exterior side of the mold forms the water pocket, and the elastomer flexes as the part strips from the core.
Interchangeable mold inserts set the inward depth of a single elongated protrusion below the lens to 3, 5 or 7 mm. Each insert forms a 45 mm long exterior concavity with an 8 mm wide opening, and its matching opposing insert maintains a 2 mm nominal wall thickness. The rear sealing edge and frame interface use common tooling, while increasing the protrusion depth increases the displacement of enclosed air.
A silicone umbrella valve mounts in a rigid seat at the lowest point of the hollow nose housing. The facepiece has a separate inward protrusion below the lens, with an exterior water pocket open to surrounding water. Exhalation through the nose raises the internal pressure and opens the valve to discharge pooled water, while the valve seats when external pressure exceeds internal pressure.
A removable carrier holds two corrective lenses behind the main lens and attaches to molded sockets on the interior of the rigid frame. The carrier positions the corrective lenses in front of the pupils and above a lower facepiece protrusion whose exterior concavity opens to the surrounding water. The protrusion occupies air space beneath the carrier, and the carrier releases from the sockets for cleaning or lens replacement.
A structured-light scanner captures the user's nose and cheek geometry, and software registers the resulting surface to the rigid frame using the pupil centers and nose bridge as landmarks. The software generates the rear sealing edge from the facial surface and shapes a lower inward protrusion with 3 mm of nominal clearance from the scanned cheeks. It offsets the protrusion surface by 2 mm to form the exterior concavity and exports the mold surfaces for machining and silicone casting.
A thin waterproof silicone adhesive band bonds a flexible flange to dry skin before water entry. The band seals across its full width, and a separate strap carries the load from the lens assembly.
A molded polycarbonate frame carries a single tempered glass lens in a perimeter groove. A snap-in retaining ring compresses a silicone gasket between the lens and the frame.
A molded silicone facepiece ends in two thin peripheral lips. Both lips flex under strap tension and seat against the brow, cheeks, and upper lip.
Two silicone protrusions extend into the air chamber above the lower sealing edge. Each protrusion has an upward-facing concave surface that collects water below the line of sight when the mask is upright.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Another conventional and yet more recently developed structure of a pair of diving masks is shown in FIG. 1, wherein a cover body 10 has a front side made of a tough material to form an outer cover 11, and an inner periphery intended to contact a wearer's face and made of a soft material to form a skirt 12, which is capable of conforming to the wearer's facial contour and thus allows the masks to be comfortably worn.A · US 2010/0077537 A1 · ¶ 5
The diving mask 10 consists of lenses 11, a frame 12 for mounting the lenses 11 and a mask 13 arranged at the frame 12.B · US 8,845,093 B1 · ¶ 18
An empty cell means only that no passage was reproduced there.
Since leakproofness of masks thus made depends on whether or not the components are tightly assembled with each other, tiny interstices between the various components may lead to leaking problems under high water pressure.A · US 2010/0077537 A1 · ¶ 4
However, this kind of structure requires a complicated manufacturing process, as explained below.A · US 2010/0077537 A1 · ¶ 5
However, specific tools are required for installation or replacement of the corrective lenses.B · US 8,845,093 B1 · ¶ 2
Thus no specific tool is required to install the corrective lenses and water tightness of the diving mask is not affected by the use of the corrective lenses.B · US 8,845,093 B1 · ¶ 4
patent.fyi, US 2026/0355584 A1, claim 1, first published 2026-11-19T13:13:53-05:00, https://patent.fyi/US20260355584/, SHA-256 178fce145264aea5a41652736705e5314a1b1c32844626da9ff9fa63f2155a39