1.1Canine and premolar anchors
Upper and lower segmental shells grip the crowns of the canines and premolars. An inclined guide on the cheek side of each pair of shells directs the lower jaw forward as the wearer closes.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Upper and lower segmental shells grip the crowns of the canines and premolars. An inclined guide on the cheek side of each pair of shells directs the lower jaw forward as the wearer closes.
A lower shell grips the mandibular teeth and carries a flat polymer pad over the molars on each side. The upper molar cusps bear against the pads, and the pad height sets the minimum separation between the jaws.
An upper tray and a lower tray each retain independently on their respective teeth. Flat inclined faces on the cheek sides of the trays engage during closure and guide the lower tray forward.
An upper tray carries a stop ledge on the cheek side of each posterior segment, and matching lugs project from the lower tray. The lugs meet the ledges at the selected closing height, and the tray walls transfer the load to the teeth.
A rigid upper shell carries a flat platform behind the upper incisors. The lower incisors contact the platform during closure, and the platform height determines the opening at that contact point.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A dental training fixture holds upper and lower molar casts on a hinged articulator. A removable spacer has two faces contoured from the casts in their opposing positions, with a solid section between the faces. Closing the articulator seats the casts against the spacer, and marking film records where each face contacts its cast.
A milled block of dental-grade polyether ether ketone forms the molar section and the interocclusal portion as one piece. The two contacting faces are machined on opposite sides of the block from aligned upper and lower molar scans. The part is finished with rounded margins, and the solid material between the machined faces carries the closing load.
A bench test set uses three spacers with nominal thicknesses of 2, 3, and 4 mm measured along the fixture closing axis at a marked reference point. All three use the same lower molar contour, and each upper contour is generated from a separate cast position at the corresponding opening. The spacers are fitted to the same hinged fixture in sequence to measure how opening changes the contact pattern.
A contoured molar spacer is used with an optical jaw tracking system that has separate marker frames on the upper and lower dental arches. The marker mounts sit toward the front of the arches, leaving the opposing molar surfaces accessible to the spacer. The tracking system records the relative position of the arches as the molars seat against the two contoured faces.
Software aligns separate upper and lower dental meshes to a digital bite record captured at the intended jaw position. It offsets the opposing molar surfaces by a specified fit clearance, trims both faces to a selected footprint, and joins their boundaries to generate a closed spacer model. The software maps local thickness across the model and flags undersized regions before exporting the geometry for fabrication.
A bench test spacer carries a thin pressure sensor array over one contoured face, with a flexible lead routed out through an edge. The face incorporates a recess sized to the sensor stack so the sensing surface follows the intended molar contour. Software converts the calibrated sensor readings into a spatial load map as opposing casts close against the spacer.
Upper and lower dental scans register in the selected jaw position. A milling machine cuts the opposing molar contours into the two faces of a rigid acrylic blank using the registered scan data.
A rigid posterior body carries a heat-softenable thermoplastic liner on each face. Opposing molar casts press into the softened liners at the recorded jaw position, and the liners retain the cusp and groove impressions after cooling.
A continuous web of rigid acrylic joins the upper and lower molar-contact surfaces. The web measures 3 mm perpendicular to the bite plane at the center of the first molar, and its outer edges are rounded.
A 2 mm polyurethane core bonds to the inner faces of two rigid molar-contact shells. The combined thickness of the core and shells sets the unloaded separation, and the core compresses under bite load.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The base portions form bite plates with generally smooth and planar bottom surfaces and with top surfaces designed to receive impression material.A · US 7,658,193 B2 · ¶ 94
The top surfaces 60 of the interocclusal portions 36 of the molar sections 32 are custom molded to fit and engage the bottom facing side of the upper molars of a specific wearer or subject. The underside surfaces 62 of the interocclusal portions 36 of the molar sections 32 are custom molded to fit and engage the top side of the bottom molars of the specific wearer of subject.B · US 2014/0261464 A1 · ¶ 80
In this manner, base material or bite plate separates occlusal surfaces of all of the user's teeth, not just the molars.A · US 7,658,193 B2 · ¶ 92
Each molar section 92 has a thick interocclusal region 96 that would be positioned between the upper and lower molars of a wearer. Each molar section 92 has a top surface 97 and a bottom surface 99 that are again molded to match the contour of the wearer's upper and lower molars.B · US 2014/0261464 A1 · ¶ 86
An empty cell means only that no passage was reproduced there.
This invention relates to interocclusal appliances worn in the mouth to prevent tooth structure loss resulting from subconscious parafunctional mandibular habits known as bruxism or clenching.A · US 7,658,193 B2 · ¶ 2
It can be difficult to properly center and align (register) the heated impressionable liner material of the nightguard relative to one's own maxillary arch.A · US 7,658,193 B2 · ¶ 7
The present invention relates generally to oral appliances and products, and more particularly to a bite regulator that regulates a wearer's jaw and bite position during use to increase oxygen, neurological, and physiological response and maintain proper neuromusculoskeletal alignment under high impact circumstances and in high stress environments.B · US 2014/0261464 A1 · ¶ 3
Some of these products are intended to be worn while participating in athletic endeavors.B · US 2014/0261464 A1 · ¶ 5
patent.fyi, US 2026/0355606 A1, claim 1, first published 2026-11-19T13:37:15-05:00, https://patent.fyi/US20260355606/, SHA-256 4d447cfcb046bfe41c46639abbb6d93f916bd18df3fd9648424bd069bdf18ae1