1.1Open frame with exposed board
Two aluminum rails support a thumb actuator, a row of finger switches, and a separate utility switch. Nylon standoffs hold the exposed circuit board between the rails, and a crossbar supports the palm.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two aluminum rails support a thumb actuator, a row of finger switches, and a separate utility switch. Nylon standoffs hold the exposed circuit board between the rails, and a crossbar supports the palm.
A camera facing the player tracks a flat optical marker fixed to the grip and measures pitch and roll relative to a calibrated resting position. The game system applies a 4-degree dead zone and maps angles up to 20 degrees to two directional axes.
A capacitive sensor under a smooth polymer strip reports the position of a single fingertip along a 55 mm surface. The game system maps position to a continuous input value and registers a tap as one action.
The control circuit checks whether the two switches close within 80 ms of each other and remain closed for 600 ms. It emits one utility event when the hold threshold is reached and rearms after both switches open.
The game system checks microphone audio for a fixed two-word phrase while the session is active. A phrase match generates the utility event for the assigned player.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Two mirrored hand units connect independently by short-range radio to a microscope workstation, and each unit contains a thumb actuator, four finger buttons, and a utility button. The left thumb actuator sets the direction and speed of the motorized specimen stage along two axes, and the right thumb actuator adjusts focus along one axis. The finger buttons trigger image capture, adjust illumination, and recall stored stage positions. The left utility button switches between coarse and fine movement, and the right utility button stops stage and focus motion.
Each hand unit retains a thumb directional actuator and a utility button, and its four finger buttons use Hall effect sensors in place of electrical contacts. Each finger button contains a spring-return plunger with a magnet that moves toward a linear Hall effect sensor mounted on the circuit board. The control circuitry samples the four sensor outputs and applies separate press and release thresholds referenced to the released reading of each button. The transmitter sends the resulting button states together with the thumb actuator and utility button states.
A telescoping bridge joins the inward faces of the hand units and sets the distance between their grip centerlines from 180 to 300 millimeters in 20-millimeter increments. An inner rectangular rail slides inside an outer rail, and the rectangular cross sections maintain the relative orientation of the grips. A spring-loaded steel pin engages one of seven holes in the inner rail, and a captive stop limits extension. Each hand unit contains its own power supply and transmitter and sends its input reports directly to the host.
Each hand unit uses a microcontroller to sample its thumb actuator, four finger buttons, and utility button at 1,000 samples per second and sends reports through its own radio transmitter. The unit sends a report when a debounced button state changes or a thumb axis changes by at least two counts on a 10-bit scale. During active input the unit sends a full state report every 4 milliseconds, and after 500 milliseconds without a qualifying change it shifts to one report every 40 milliseconds. A new input change restores the 4-millisecond interval, and each report carries a unit identifier and sequence number for tracking the two streams independently.
Two hand units attach to adjustable mounts on a simulator seat, and a separate floor pedal assembly supplies rudder input. The left thumb stick supplies throttle and trim commands, while the right thumb stick supplies pitch and roll commands. Each hand unit transmits its stick and button states to a receiver, and host software maps the finger and utility buttons to simulator functions such as braking, flap adjustment, and view centering. The simulator reads the pedals as a separate input device and combines their rudder axis with the hand controls.
Each hand unit digitizes its two thumb stick axes and sends raw readings together with the states of its four finger buttons and utility button. Holding both utility buttons for two seconds starts a calibration routine that records the median of 100 samples from each released axis and then records axis extrema during a full sweep of each stick. The host computes a per-axis dead zone from the variation in the released samples and scales the positive and negative travel separately using the recorded extrema. The host stores the calibration profile for each unit and applies it to subsequent input reports.
A spring-centered thumbstick moves a permanent magnet with a two-axis gimbal. Two Hall-effect sensors measure lateral and longitudinal deflection, and the control circuit applies a 5 percent center dead zone.
Four acetal levers pivot on separate steel pins along the underside of the grip, with one lever under each finger. Each lever closes a tactile switch after 1.2 mm of travel at its contact pad.
Two molded polycarbonate halves enclose the circuit board and fasten together with screws seated in brass inserts. A textured thermoplastic elastomer overmold covers the palm contact area.
A 2.4 GHz transmitter sends a report every 8 ms over a short-range radio link. Each report carries the current button states, two signed 12-bit directional values, and a sequence number.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In one embodiment, the present invention provides a thumb joystick for use on or over a touch screen of an electronic device.A · US 9,170,658 B2 · ¶ 9
In an exemplary embodiment, a control box and operator interface for an industrial vehicle includes a left thumb joystick controller, a right thumb joystick controller, and integrated handles positioned adjacent the left thumb joystick controller and the right thumb joystick controller, respectively.B · US 2019/0177140 A1 · ¶ 6
An empty cell means only that no passage was reproduced there.
As a touch screen is flat and smooth, activating a virtual button does not give a tactile feedback to a user; lack of a tactile feedback on a touch screen 10 gives a poor sensory experience, especially to a user for playing a game, say on an iPad or smartphone, when the user can rarely take one's eyes away from the screen.A · US 9,170,658 B2 · ¶ 3
The present invention provides a self-centering tactile thumb joystick for use to control a virtual directional pad on a touch screen of an electronic device, such as, smartphones, ipads, remote controllers for smart television sets and so on that require navigation inputs.A · US 9,170,658 B2 · ¶ 8
Existing layouts are prone to inadvertent operation of the controllers by an operator leaning against a controller or a controller getting caught in an operator's coat or the like.B · US 2019/0177140 A1 · ¶ 4
The described embodiments provide new features and improvements but retain the traditional grouping of controls known from existing machines, thus allowing for easy transition to the improved designs.B · US 2019/0177140 A1 · ¶ 5
patent.fyi, US 2026/0355622 A1, claim 1, first published 2026-11-19T13:37:15-05:00, https://patent.fyi/US20260355622/, SHA-256 f8b5e9b51f886ed8da1969506a0c276ca32396ccc7ec5b52d3dd85e01c017c97