1.3Moving permanent magnet
A gearmotor turns an eccentric cam that slides a permanent magnet toward and away from a steel tab on the pivoted head. The head tilts as the gap closes, and a torsion spring returns it as the gap opens.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A gearmotor turns an eccentric cam that slides a permanent magnet toward and away from a steel tab on the pivoted head. The head tilts as the gap closes, and a torsion spring returns it as the gap opens.
A coil and steel core mount to a pedestal beneath the end of a pivoted rocker. The energized coil pulls a steel tab on the rocker downward, and a spring lifts the rocker when current stops.
A gearmotor turns a single-lobe cam at 60 revolutions per minute. The cam closes a switch in the coil circuit for one-quarter of each turn, and a return spring resets the head between pulses.
The coil current gives the core face the same polarity as the face of the permanent magnet across the gap. Repulsion lifts the rocker about its pivot, and a torsion spring returns it when current stops.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Two display stands each carry a lightweight sign on a pivot above the sign’s center of mass. One sign houses an electromagnet near its inner edge, and the facing sign carries a steel plate across an air gap. A timer energizes the coil through a transistor, drawing both signs inward until stops limit their travel. When the pulse ends, gravity returns the signs toward vertical and they swing about their pivots.
Two display housings each contain a shallow liquid reservoir that supports a floating panel in place of a solid joint. Loose guide posts pass through oversized holes in each float and limit sideways drift while permitting tilt. An electromagnet and a steel target sit above the liquid on facing panel edges, and fine flexible leads carry current to the coil. Each current pulse tilts the panels inward, and buoyancy levels them after the pulse.
Two figures carry pivoted heads with an electromagnet and a steel target positioned across the gap between them. A supercapacitor bank replaces the battery as the coil’s pulse supply, and a current-limited charger replenishes the bank between cycles. Once the bank reaches its operating voltage, a controller switches it across the coil through a transistor, and a flyback diode carries coil current when the transistor opens. Gravity restores the heads while the charger replenishes the bank.
Four figures stand in a row as two pairs, with each pair carrying a 12-volt electromagnet in one moving head and a steel target in the facing head. Each magnet and target face across a 3-millimeter gap at rest, and stops limit their combined inward travel to 2 millimeters. A controller drives the first coil for 80 milliseconds and begins the second coil pulse 200 milliseconds after the first begins. The controller repeats the sequence every 2 seconds while the heads swing freely between pulses.
An electronic game scoreboard carries two mascots on separate pivots above the score display. One mascot contains a coil near its facing edge, and the other carries a steel target opposite the coil. An isolated input connects the scoreboard’s point relay to a controller, which detects the relay closure and drives the coil through a transistor for a fixed interval. Gravity returns the mascots toward their rest positions after the pulse.
Two figures carry pivoted heads with a coil in one head and a facing steel target in the other. An optical encoder reads the angle of the coil-bearing head at its pivot, and a controller records the peak angle after each current pulse. The controller compares that peak with a setpoint and adjusts the next pulse width within preset limits. It waits for the measured angle to settle near rest before issuing another pulse.
A torsion spring connects the head to the body, and a steel plate sits inside the body below an electromagnet in the head. A current pulse draws the head toward the plate, and the spring returns the head when the pulse ends.
A hand crank spins a permanent-magnet generator whose windings feed the electromagnet through a switch. Closing the switch as the crank turns energizes the coil, and opening it lets the return spring lift the rocker.
A stainless steel helical spring joins the rocking head to the body, with its end turns captured in molded sockets. The spring bends under magnetic pull and straightens when the pull subsides.
A copper coil wound around a low-carbon steel core fits inside the rocking head. A 1 mm thick low-carbon steel target sits inside the body across a 3 mm gap from the core face at rest.
Four series-connected rechargeable cells feed a 4.8 V nominal rail for the electromagnet. A transistor switches coil current, and a diode across the coil carries the inductive current after the transistor turns off.
A microcontroller timer turns on the coil driver for 100 ms every 800 ms. Each pulse draws the steel target toward the coil, and the spring returns the head during the 700 ms off interval.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Springs 47a-d may have first ends positioned and secured in spring recesses 27a-d of base 20, respectively, and second ends positioned in spring recesses 37a-d of platform 30, respectively. Bearing 45 may be positioned between socket 25 of base 20 and socket 35 of platform 30.A · US 2013/0309935 A1 · ¶ 70
In some other non-limiting examples, magnetic members in the base (e.g., magnetic members 43a-d) may comprise permanent magnets and magnetic members in the platform (e.g., magnetic members 44a-d) may comprise electromagnets.A · US 2013/0309935 A1 · ¶ 73
A ferric material (66) is attached to the lower portion (86) of the vertical rod (64). A pair of electromagnetic coils (80) are positioned on opposing sides of the ferric material (66), inserted into the pivot support (70).B · US 2018/0256994 A1 · ¶ 43
The electromagnetic coils (80) may be controlled by a microcontroller, producing two opposing pulse width modulation sequences. By connecting the coils (8) to the microcontroller, and using transistors as buffers, the coils (80) can be energized in small, opposite increments which would ensure a clean, fluid motion of the vertical rod (64), and minimal power usage.B · US 2018/0256994 A1 · ¶ 44
An empty cell means only that no passage was reproduced there.
It is therefore desirable for apparatuses and systems for imparting motion to a bobble toy which are contactless and programmable.A · US 2013/0309935 A1 · ¶ 6
Several embodiments of the present invention relate to electromagnetically operated apparatuses and systems for vibrating a platform upon which a bobble toy rests.A · US 2013/0309935 A1 · ¶ 7
Thus, what is needed is a means to periodically excite the bobbling portion of a bobbling novelty toy doll.B · US 2018/0256994 A1 · ¶ 7
A bobbling toy exciter for exciting a bobbling portion of a bobbling toy is provided.B · US 2018/0256994 A1 · ¶ 8
patent.fyi, US 2026/0355643 A1, claim 1, first published 2026-11-19T14:02:27-05:00, https://patent.fyi/US20260355643/, SHA-256 6867b22e58403bc6fc6e674ac68c7dd42d5d5fed5ffab90343bad860dd5c8008