1.1Loads through a ladder frame
Bolted crossmembers keep the rails spaced apart and support the axle brackets. The rails carry longitudinal reactions, and clips transfer pressure from the removable cover into the frame.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Bolted crossmembers keep the rails spaced apart and support the axle brackets. The rails carry longitudinal reactions, and clips transfer pressure from the removable cover into the frame.
An aluminum floor panel with two upturned edge flanges carries bending loads between the axle supports. Transverse ribs spread bracket loads across the floor, and the top remains open.
Split collars wrap around the shell at the axle stations. Broad contact bands distribute bracket reactions around the shell circumference and limit local ovalization.
Fore-and-aft sliding clips support the cover vertically and laterally, and a locating tab transfers cover drag to the front axle crossmember. A longitudinal member carries the drive reaction directly to the rear axle crossmember.
Each side uses upper and lower rods joined by diagonal braces, and transverse rods connect the two sides. Axle brackets and fairing clips attach at frame joints, where the rods transfer loads through tension and compression.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An electric camera carrier runs along a guideway between greenhouse benches and uses a closed body tube with transverse internal plates. The forward plate supports a camera bracket, and the rear plate supports a geared motor that drives an axle through a timing belt. Both plates attach around their perimeters so the shell carries camera drag and drive reactions between the mounts.
Form each transverse diaphragm from sheet aluminum with a drawn perimeter flange that follows the inside of the body tube. Bond the flange to the tube and bolt the electric drive bracket to the face of the rear diaphragm. The flange spreads the drive reaction along the shell, and a forward diaphragm transfers aerodynamic loading between the nose and the shell.
Use a body tube 300 mm long and 60 mm in outside diameter, with internal plates at 30, 100, 200, and 270 mm from the nose. Bond each plate around its perimeter and mount a geared electric drive to the two aft plates. The two forward plates support the nose and front axle bracket, and the shell carries axial and bending loads between the mounting stations.
Place the electric vehicle on a roller dynamometer with its driven wheels on the instrumented rollers and a restraint attached to a forward internal plate. Aim a ducted bench fan along the body tube to apply aerodynamic loading while the rollers impose a controlled drive load. The rear motor plate, forward restraint plate, and outer tube share the resulting loads as the dynamometer records wheel torque and speed.
Mount a reversible electric motor and its reduction gear to a rear internal plate, and mount the battery tray across two forward plates. A bidirectional motor controller returns energy to the battery during braking within the battery charge acceptance limit. The rear plate transfers drive and braking reactions into the body tube, which carries them to the forward plates along with aerodynamic loads on the shell.
Bond axial strain gauges to opposite sides of the body tube between the forward and rear internal plates. A controller averages the two readings to track axial strain and differences them to track bending along the gauge axis. When either reading exceeds its configured limit, the controller lowers the electric motor current command and logs the strain readings and current command.
Circumferential rows of rivets join flanged aluminum plates to the inside of a thin aluminum tube. The plates spread concentrated bracket reactions into the tube wall and restrain changes in its cross section under aerodynamic loading.
Wide adhesive fillets bond glass fiber laminate bulkheads to the inner wall of a glass fiber tube. The bonded joints transfer shear between the wall and plates as the assembly carries external pressure and longitudinal reactions.
Thin plywood skins wrap around transverse plywood plates and meet at bonded longitudinal lap joints. The plate bonds spread local support reactions into the skins, and the closed shell carries bending and torsion between plate stations.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The bulkhead member is then bent along the fourth side of the weld access opening and shaped into a folded configuration that includes a vertical portion spanning the distance between the opposing faces of the frame member, and a horizontal portion to facilitate welding to the opposing face. The provision of the internal bulkhead member increases stiffness in the tubular frame member and reduces the matchboxing effect associated with hydroformed tubular frame members.A · US 7,380,876 B1 · abstract
All or most of the load on the aid is taken by the surface or skin. Semi-monocoque construction is a hybrid structure in which a surface, skin, or shell is reinforced with rings, ribs, or frames to help carry the stress of a load, for example.B · US 2020/0188218 A1 · ¶ 28
An empty cell means only that no passage was reproduced there.
During this torsion cycle, the hydroformed tubes tend to matchbox, which creates higher loading in the tube-to-tube and tube-to-cowl joints and can cause material fatigue and cracking.A · US 7,380,876 B1 · ¶ 5
There is a need for a front end construction that may incorporate the use of hydroformed tubes that provides superior stiffness and rigidity capabilities.A · US 7,380,876 B1 · ¶ 7
These devices are used to assist people in the act of walking or standing by providing weight bearing and/or balance assistance.B · US 2020/0188218 A1 · ¶ 3
Such tubular frame-based assemblies are complex to manufacture and assemble and suffer from multiple joinders and other contact points.B · US 2020/0188218 A1 · ¶ 4
patent.fyi, US 2026/0355645 A1, claim 1, first published 2026-11-19T14:02:27-05:00, https://patent.fyi/US20260355645/, SHA-256 9fcfa4fe4f5849627730a5494de0a4771928fe3bf8249f17514c9d511f7bc8ce