1.2Individually mounted filter cups
Spring clips grip the rims of individual polymer cups at positions set by two rails. Each cup has its own open mouth for sample loading and a perforated base that drains into a collector below the frame.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Spring clips grip the rims of individual polymer cups at positions set by two rails. Each cup has its own open mouth for sample loading and a perforated base that drains into a collector below the frame.
A rigid ring clamps the perimeter of a molded polymer sheet with integral wells and perforated floors. Radial tension limits sheet deflection during low-pressure filtration while the space beneath the wells remains open for drainage.
A continuous plate provides a drain bore under each well and a flat sealing surface beneath the array. A patterned gasket seals each bore to a dedicated channel in the manifold, which routes each filtrate stream to its own outlet.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A circular well array captures coarse abrasive grains from a dilute grinding wash stream. Each well mouth admits the coarse grains, and each bottom bore passes water and finer particles while retaining the coarse fraction. Blind slots in the support layer run between neighboring bottoms and leave a continuous web beneath the well walls. A reverse water pulse lifts the retained grains into a collection trough.
A laser-machined stainless steel foil replaces the well-bottom support sheet beneath a molded thermoplastic well layer. A fixture aligns one drilled bore with each circular well opening, and a patterned adhesive bonds the foil to the wall lands. Intermittent through-slots beneath the wall lands divide portions of the foil between neighboring bottoms, and uncut metal bridges keep the sheet continuous. Each bore passes the carrier liquid and retains rigid particles wider than the bore.
A 12 by 12 array uses circular well openings 3 mm in diameter on a 6 mm pitch, with a well depth of 1.5 mm. A 0.5 mm thick support plate carries a 0.3 mm bore under each well, and 0.25 mm deep slots run between adjacent bottoms on the underside of the plate. Rigid resin beads 0.8 to 1.2 mm in diameter enter through the well mouths and remain in the wells as rinse liquid drains through the bores.
A gasket clamps the well array between a transparent flow chamber and a drain manifold in an optical particle imaging system. The chamber distributes a suspension of rigid calibration particles over the well mouths, and suction at the manifold draws carrier liquid through the bottom bores while retaining the particles. Blind slots between neighboring well bottoms leave a continuous barrier between the chamber and the manifold except at the bores. A camera above the transparent cover records the retained particles through the well mouths.
A swing-out centrifuge bucket holds the well array in a gasketed cartridge above a filtrate cup. Each well mouth admits rigid sample granules, each bottom bore retains them, and blind slots partly divide the support layer between neighboring bottoms. During rotation, the bucket swings outward so the filtrate cup sits farther from the axis than the well mouths, and centrifugal force drives rinse liquid through the bores into the cup. The cartridge lifts out after the rotor stops, and the granules are recovered through the well mouths.
A motorized positioning stage holds a well array above a drain chamber, and an overhead camera images each well after a dispensing head delivers a suspension of rigid beads. Each well has a bottom bore smaller than the beads, and underside slots partly divide the support layer between neighboring bottoms. Image processing identifies empty wells from their contrast against a reference image of the unloaded array, and the controller moves those wells beneath the dispensing head for another dose. The controller repeats imaging after each dose and ends the run when every well is occupied or a preset retry count is reached.
Each well has a solid glass floor, and a sidewall slit just above the floor connects to a drain manifold. A downstream pressure drop draws the carrier liquid through the 3 µm-high slit while retaining rigid particles at least 10 µm across.
An outlet 40 µm in diameter drains carrier liquid from a well loaded with 10 µm magnetic particles. A magnet beneath one edge of the well holds the particles against the floor beside the outlet while liquid flows through it.
An annular shoulder inside each bore seats a perforated metal disk, and a retaining ring holds the disk against the shoulder. A rigid perimeter plate carries the well layer and leaves the undersides of the disks exposed to a common drain cavity.
A 1 µm-thick silicon nitride film forms the floor of each well. Lithographic patterning and dry etching form 2 µm circular through-holes that pass carrier liquid and retain rigid particles at least 5 µm across.
An injection-molded polypropylene layer contains a square array of tapered through-openings. Each opening narrows from 500 µm at the entry to 250 µm at the base, providing clearance for 100 µm particles throughout the opening.
A 300 µm-thick silicon carrier supports the well layer on raised lands around the wells. A patterned adhesive bonds the layers at the lands and leaves the drainage regions clear.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Often it is not appropriate to subject cells to an electric field for long periods, and so a possible embodiment of the invention comprises a semipermeable membrane 9 which prevents the cells from falling into the channel 10 when the applied voltages are removed.B · US 9,039,883 B2 · ¶ 52
In this structure through-holes are opened, intended to form the actual well, suitable for receiving the liquid; the walls of the hole can be treated to give the required hydrophilic characteristics.B · US 9,039,883 B2 · ¶ 54
This involves the laying of fiber strands for mechanical reinforcement (“rovings”), which are in turn formed by a multiplicity of discrete reinforcing fibers running parallel to one another, along any desired path curve and attaching them with the aid of fixing threads on a backing layer to form a fiber preform (“preform”), whereby the alignment of the individual fiber strands can be adapted virtually optimally to the flux of force acting on the finished composite component.A · US 2009/0050259 A1 · ¶ 6
An empty cell means only that no passage was reproduced there.
With conventional semifinished products, such as, for example, woven or laid fiber fabrics, for reinforcement of the polymer material, not all conceivable fiber orientations can be realized, since the reinforcing fibers are generally arranged there in a specific, fixed orientation.A · US 2009/0050259 A1 · ¶ 5
The optimum utilization of the mechanical load-bearing capacity of the fiber strands that is achieved in this way can minimize their number, and consequently also considerably reduce the weight of the fiber preform.A · US 2009/0050259 A1 · ¶ 6
The present invention concerns techniques for selecting and modifying particles such as single cells, microorganisms and small aggregates thereof.B · US 9,039,883 B2 · ¶ 2
The need to combine impedance measurements with the controlled motion of the analysed material remains however unfulfilled; this deficiency severely affects the quality of the measurement.B · US 9,039,883 B2 · ¶ 6
patent.fyi, US 2026/0355656 A1, claim 1, first published 2026-11-19T14:02:27-05:00, https://patent.fyi/US20260355656/, SHA-256 a5737549b3e9b4931ae5c9a839160ae63e055d634371c2cbafd8b29bba69a3b4