1.1Grids compacted from powder
A shaped die compacts stainless steel powder into two annular grids with ribs and open slots. Sintering bonds the powder particles, and the facing ribs meet at crossings when the grids are assembled.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A shaped die compacts stainless steel powder into two annular grids with ribs and open slots. Sintering bonds the powder particles, and the facing ribs meet at crossings when the grids are assembled.
A laser cuts straight through-slits along rays projected from a point inside the central opening of each plate. The two projected points sit on opposite sides of the disc axis, so the remaining ribs cross over much of the annulus while the open slots lead toward the hub.
A laser fuses stainless steel powder to build the lower grid, temporary supports, and upper ribs in one build. The upper ribs fuse to the lower ribs where they cross, and removal of the supports and loose powder opens the drainage passages.
An outer retaining ring and a ported inner hub clamp the two grids at their edges. The ribs bear against one another at the crossings under filtration pressure, and hub ports collect filtrate from the open channels.
An investment mold defines the inner and outer rims and the slots between ribs in each grid. A gate on a sacrificial tab away from both rims feeds the casting, leaving the mold to establish both circumferential edges.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Commercially pure titanium sheets replace stainless steel sheets in a retainer for chloride-bearing process water. A laser cuts parallel through-slits in each blank while leaving solid bands at the inner and outer edges. A fixture holds the blanks with mirrored rib directions while a pulsed laser welds the crossings under argon shielding. Trimming removes the solid bands and opens the spaces between the ribs to the central collection opening.
A nickel-based brazing paste replaces individual spot welds at the crossings of two slitted stainless steel blanks. A dispenser places a metered dot of paste at each mapped crossing on the lower blank, and a fixture clamps the upper blank in the mirrored orientation. A vacuum furnace heats the assembly above the filler melting temperature and below the plate melting temperature so that the filler wets both rib faces and solidifies into a joint on cooling. A cutting operation removes the inner and outer margins after brazing.
A laser cuts the parallel through-slits and three registration holes in the sacrificial margin of each metal blank. A backlit camera measures the slit edges and registration holes of each blank before a robotic fixture stacks the blanks with mirrored rib directions and clamps their margins. A second image locates the registration holes in the stacked pair, and software maps the measured rib centerlines into fixture coordinates to calculate the crossing locations. A numerically controlled laser welds those locations before a cutting head removes the inner and outer margins.
Two 0.8 mm stainless steel sheets of the same grade supply the flat blanks. Roller leveling reduces bow before the slit pattern is cut.
A fiber laser cuts straight 0.6 mm through-slits on a 1.8 mm pitch in each blank. All slit centerlines in each blank share a common direction, and the ends stop in sacrificial bands at the inner and outer edges.
Two dowel pins engage registration holes in sacrificial tabs and set the rib directions at 90 degrees to each other. A platen presses the facing plate surfaces together while two tack welds on the tabs hold the alignment.
A focused laser pulse melts the upper rib and the contacting surface of the lower rib at each crossing. The molten metal solidifies into a localized joint between the ribs.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
As an example, the support frame plate 120 and the platform 125 may be made from stainless steel.A · US 2007/0177708 A1 · ¶ 27
The plate 52 includes an opening which aligns with an opening on a block 49. Once aligned, a retainer bolt 90 may be inserted for fastening the retainer plate 52 to the inlet mixer 41.A · US 2007/0177708 A1 · ¶ 23
Using an electrical discharge machining apparatus employing a preformed cylindrical electrode, an aperture of predetermined diameter is drilled through a planar, tungsten carbide plate. Using a wire electric discharge machining apparatus, annular blanks are cut from the planar tungsten carbide plate, the outer surface of the annular blank being cylindrical and concentric with the inner, drilled surface of the annular blank.B · US 9,155,363 B2 · abstract
An empty cell means only that no passage was reproduced there.
EDM may be well-suited for cutting intricate contours or delicate cavities that would be difficult to produce with a grinder, an end mill or other cutting tools.A · US 2007/0177708 A1 · ¶ 4
Because EDM works with materials that are electrically conductive, metals that can be machined may include, for example, but not limited to, hastalloy, hardened tool-steel, titanium, carbide, inconel and kovar.A · US 2007/0177708 A1 · ¶ 4
The problem with such materials is that, because of their hardness, they are extremely difficult to work with in order to produce attractive jewelry designs.B · US 9,155,363 B2 · ¶ 5
This greatly expands the spectrum of ornamentation that can be created.B · US 9,155,363 B2 · ¶ 7
patent.fyi, US 2026/0355658 A1, claim 1, first published 2026-11-19T14:02:27-05:00, https://patent.fyi/US20260355658/, SHA-256 5470d43bd1665dadbb053c25d0947c1dd0cbcc4131a32cec4bfee185d2669faa