1.1Flat clamp bars on rails
Each primary rail presents a flat rail face along the filter perimeter. Screws draw a removable clamp bar toward that face, compressing the reinforced edge panel and a flat gasket between them.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Each primary rail presents a flat rail face along the filter perimeter. Screws draw a removable clamp bar toward that face, compressing the reinforced edge panel and a flat gasket between them.
The primary rails have slots that open toward the center of the frame. The rails move laterally over the reinforced edge panels before the secondary rails lock the corners and hold the primary rails at a fixed spacing.
Each unreinforced media margin folds around a removable elastomer cord and enters an upstream-facing slot. The compressed cord presses the media against the slot walls to retain the margin and seal the joint.
Round crossbars span between blind sockets in the primary rails, with one bar near each secondary media edge. A flat gasket bonded to each secondary rail seals against the side of the media pack while the crossbars carry the pressure load.
A clamp strip compresses a flat impermeable gasket over each secondary media margin, and the gasket's inner edge sets the boundary of the exposed media. Each downstream flange underlies the media margin and ends short of the exposed opening.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A rectangular frame mounts on the air intake of a rail vehicle traction electronics cabinet. The reinforced edges of hydrophobic pleated media insert into upstream-opening slots in the primary rails, and inward flanges on the secondary rails support the downstream side of the corrugated edges. A hinged intake grille retains the media in the slots, and a closed-cell gasket seals the frame against the cabinet opening.
Perforated stainless steel strips replace the integral downstream support flanges on the secondary rails. Each strip fastens to the downstream face of its rail and projects inward under the corrugated edge of the pleated media. A solid band along the strip's outer margin carries a compressible edge seal, and the perforated inner margin passes air through the supported portion of the media.
Replaceable extruded elastomer channels form the upstream-opening slots in place of slots formed directly in the rigid primary rails. Each channel has a barbed base that presses into a longitudinal groove in the rail and two flexible lips that grip the reinforced edge panel. The downstream flanges on the secondary rails support the corrugated edges, and the channel lips flex outward when the media is pulled upstream for removal.
Four rails form a frame with a 600 mm by 600 mm clear opening for media with a 100 mm pleat depth and a 25 mm pleat pitch. Each primary rail has a 25 mm deep slot aligned with the airflow axis and sized to leave 0.5 mm of total clearance around a 2 mm thick reinforced edge panel. Each secondary rail has a downstream flange that projects 20 mm inward, and a removable upstream retainer bar holds the edge panels in the slots.
A slide-in rack holds the rectangular frame on the outdoor air path between the intake louver and a fixed-plate heat exchanger. Upstream-opening slots capture the reinforced media edges, and the downstream secondary flanges carry the corrugated edges under airflow load. Closing the service door actuates a cam that presses the frame gasket against a shoulder in the rack and seals the path around the media.
A differential pressure sensor connects to static pressure taps upstream and downstream of the framed media, and a duct airflow sensor measures volumetric flow. During commissioning, a controller records clean-filter pressure drop at several flow rates and stores a baseline curve. During operation, the controller subtracts the interpolated baseline at the measured flow from the measured pressure drop and signals service when the excess stays above a configured threshold for ten minutes.
Each extruded aluminum primary rail has a continuous upstream-facing slot with a depth axis at 0 degrees to the upstream-downstream axis. The slot is 8 mm deep and receives a 2 mm thick reinforced edge panel with a slip fit.
Each molded primary rail has an upstream-open slot with a depth axis at +25 degrees to the upstream-downstream axis. A ribbed elastomer liner compresses against the reinforced edge panel as the panel enters the slot.
Each formed steel secondary rail has an integral downstream flange that extends 12 mm inward from the rail body. The flange supports the secondary media margin, and its free edge forms the secondary boundary of the filtration opening.
Each molded polymer secondary rail has a downstream flange that projects 10 mm inward and supports the media margin. Gussets on the downstream face stiffen the flange, and the straight inner edge defines the secondary boundary of the filtration opening.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The contact support pedestal 3 disposes perimeter walls 4 outside the edges of the holding cavity 2 opening, and the edges of the holding cavity 2 opening formed by the upper case 1A establish the overhanging regions 14 that protrude inside the rectangular holding cavity 2.A · US 8,120,318 B2 · ¶ 33
Corner angular member junctions 5 and middle angular member junctions 7 have an upward-extending flange 35 preferably composed of metal or pressed metal with an angle greater than or equal to 90 degrees. These flanges serve to secure and locate the container 2, when pallets 1 are nested, the flanges 35 effectively conceal the square framework along the perimeter of the metal base pallet 1.B · US 10,800,576 B1 · ¶ 35
An empty cell means only that no passage was reproduced there.
A battery charger with this structure can charge different types of battery packs with different thicknesses, but it has the drawback that it cannot charge battery packs with different external shapes.A · US 8,120,318 B2 · ¶ 5
The battery charger described above has the characteristic that it can charge different types of battery packs with different external shapes, and it can charge different types of battery packs with electrode terminals located without restraint on the perimeter terminal surfaces.A · US 8,120,318 B2 · ¶ 8
This gives rise to concerns about the packaging system not being able to function due to missing parts, etc.B · US 10,800,576 B1 · ¶ 7
Existing packaging systems fall short of this optimum.B · US 10,800,576 B1 · ¶ 8
patent.fyi, US 2026/0355664 A1, claim 1, first published 2026-11-19T14:02:27-05:00, https://patent.fyi/US20260355664/, SHA-256 644085c837caa9265834d248f821f9880335a1a63dfa734ea513fb1b31fa21cd