1.1Threaded shell closure
An external thread on the lower shell engages an internal thread on the upper shell. Rotation compresses a silicone gasket between annular faces and seals the joint around the recovery cavity.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
An external thread on the lower shell engages an internal thread on the upper shell. Rotation compresses a silicone gasket between annular faces and seals the joint around the recovery cavity.
A molded polypropylene cup defines the cavity with a continuous sidewall and base. A gasket seals the cup rim against the fixed manifold, and a perforated insert holds tissue above a drain in the base.
A hose barb molded into the lower shell connects to the aspiration line above the perforated screen. The port directs the incoming stream along the cavity wall, and liquid exits through the screen into the outlet beneath it.
A sealed receiver holds aspirate during suction. Once suction stops, the upper shell swings clear and a peristaltic pump discharges the aspirate through a wide-bore tube positioned over the lower shell.
A vertical chamber with a conical sump holds each batch at rest so tissue denser than the carrier liquid settles into the sump. An adjustable withdrawal tube draws liquid from the surface and stops above the settled layer.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A removable filter with buckled upper and lower shells sits in a drain housing on an industrial parts washer. A branch from the washwater return line directs liquid through a hole in the upper shell. A perforated plate in the lower shell retains machining fragments and drains washwater back to the sump. The operator isolates the branch and separates the shells to inspect the retained fragments.
A stainless steel wedge wire screen forms the filtration surface across an opening in the lower shell. A retaining ring compresses a perimeter gasket between the screen frame and the lower shell. The wide faces of the wires face the cavity, and the slots widen toward the drain side. Liquid entering through the upper shell passes through the slots while tissue wider than the slot openings remains in the cavity.
Three radial lugs on the lower shell engage matching L-shaped slots on the upper shell in place of buckle tabs. The upper shell seats over a face gasket and rotates through a quarter turn to compress the gasket between the shell flanges. Aspirated liquid enters through a central hole in the upper shell and drains through the screen in the lower shell. Reverse rotation releases the upper shell for access to the retained tissue.
Two divider walls in the lower shell form three cavities with a volume of 15 milliliters each. The common upper shell has one 5 millimeter inlet per cavity and compresses a gasket against the divider walls when the shells buckle together. A three-position selector valve routes aspirate to one inlet at a time. A separate mesh panel in the floor of each cavity retains tissue as liquid drains into a shared chamber beneath the panels.
A filter housing connects inline between a surgical suction handpiece and a suction canister whose vacuum port connects to a regulated vacuum source. The handpiece tubing couples to the upper-shell inlet, and the housing outlet beneath the lower-shell screen connects to the canister inlet. Vacuum draws aspirate through the filter cavity and carries filtrate to the canister while the screen retains tissue. Shutoff valves on both sides of the housing isolate it before filter removal.
One pressure sensor connects to a tap in the filter cavity and a second connects to a tap in the drain chamber below the lower-shell screen. A controller calculates the pressure drop across the screen while suction is active. If the drop stays above a stored threshold for two seconds, the controller closes a motorized valve on the suction line and displays a filter service alert. The controller reopens the valve after an operator reset.
A transverse hinge pin joins molded polypropylene shells along one edge. A cantilever latch on the opposite edge engages a molded shoulder and compresses a silicone rim gasket around the cavity.
An integral hose barb surrounds a through-hole in the upper shell and grips flexible aspiration tubing. A radiused inner lip guides the incoming liquid and tissue into the cavity.
A stainless steel disk with 0.8 mm round perforations rests on a molded shoulder above the lower outlet. A retaining ring clamps the disk against a perimeter gasket so liquid passes through the perforations while larger tissue fragments remain in the cavity.
A polypropylene frame holds a woven polyester mesh with 300 µm nominal openings in a recess in the lower shell. Molded ribs support the mesh against the suction pressure differential and leave drainage channels between the mesh and the outlet.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Alternatively the collection chamber may be a separate chamber that is detachable from the filter chamber and housing.A · US 2012/0024773 A1 · ¶ 80
a mesh strainer in an upper portion of the filter chamber and oriented relative to the water inlet such that water flowing into the filter chamber from an inlet flows across the mesh strainer, the mesh strainer filtering particulate matter from water flowing through it to the outlet, wherein in useA · US 2012/0024773 A1 · ¶ 7
Accordingly, both suction inlets 110a, 110b are in fluid communication with the suction port 124, which connects both aspirators 102, 104 to the same device 126, such as a device requiring a vacuum or a vacuum reservoir.B · US 2016/0053727 A1 · ¶ 17
The mesh strainer strains water or liquid flowing into the filter as the water flows into the inlet and out of the outlet. The mesh strainer filters out particulate matter from the flow through the filter.A · US 2012/0024773 A1 · abstract
An empty cell means only that no passage was reproduced there.
The invention relates to a filter for use in a washing appliance in particular the filter is particularly suited for use in domestic dishwashing or laundry appliances.A · US 2012/0024773 A1 · ¶ 1
However over a long term the water softener performance can be adversely affected by contamination and clogging by solid particles entering in the mains supply water.A · US 2012/0024773 A1 · ¶ 3
Engines, for example vehicle engines, are being downsized and boosted, which is reducing the available vacuum from the engine.B · US 2016/0053727 A1 · ¶ 3
A shut-off valve is positioned in a flowpath of the second aspirator to shut off the flow therethrough without shutting off a flow through the first aspirator.B · US 2016/0053727 A1 · ¶ 8
patent.fyi, US 2026/0355736 A1, claim 1, first published 2026-11-19T14:56:45-05:00, https://patent.fyi/US20260355736/, SHA-256 5deaa5c4f22b5896e5a4e458084279d3b42f6ad4938d9c697b08522f4241e23f