1.1Water feed through the rim
A bracket on the inner cylinder supports a bent supply tube that passes over both rims. The tube connects to an annular header that distributes pressurized water to the nozzle entries.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A bracket on the inner cylinder supports a bent supply tube that passes over both rims. The tube connects to an annular header that distributes pressurized water to the nozzle entries.
The cavity floor slopes toward a screened sump connected to a self-priming diaphragm pump. The pump pushes wastewater through a hose clipped over the rim and into a collection tank.
Four welded polymer panels carry inward-facing nozzles in drilled mounting holes. A sloped floor directs wastewater to a corner drain that passes through an opening in the outer cylinder.
Brackets suspend an annular manifold below the chamber rim. Inward-facing nozzles thread into the manifold, which receives pressurized water from a supply tube at the rim.
A 1 mm bore runs through a stainless steel insert and discharges a narrow jet into the cavity. The mounting angle sets the direction of each jet, and staggered nozzle rows distribute the jets along the wash cavity.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A parts washer uses nested cylinders with a water inlet in the outer cylinder and a drain from the inner cylinder passing through the outer wall. Nozzles seated in apertures in the inner cylinder each have an inlet and an outlet connected by a basin with an ellipsoidal outlet portion. Polymer saddles support a machined shaft along the chamber axis while the nozzles rinse away loose chips and water-soluble machining fluid. A removable mesh basket below the drain collects chips.
A gasketed rectangular stainless steel housing replaces the outer cylinder and surrounds a cylindrical wash chamber. The housing and chamber wall form a supply plenum that feeds nozzles seated in the chamber apertures. Each nozzle has a basin with an ellipsoidal outlet portion connecting its inlet and outlet. A welded drain tube passes from the chamber floor through the plenum and the housing wall, keeping runoff separate from the pressurized supply.
Each inner-cylinder aperture holds a rigid nozzle cartridge with a molded silicone slit diaphragm in place of the rigid outlet aperture. The cartridge inlet feeds a basin whose ellipsoidal outlet portion terminates at the diaphragm. Supply pressure deflects the diaphragm and opens the slit into a narrow slot that directs water into the chamber. The slit closes when pressure falls, and runoff exits through a drain that crosses the outer cylinder wall.
An inner cylinder with a 70 mm bore and a 120 mm usable length fits inside an outer cylinder with a 90 mm bore. Two rows of four nozzles sit 40 mm apart, and each nozzle has an ellipsoidal basin portion opening through an outlet measuring 1.0 mm by 0.5 mm. A regulator maintains 80 kPa gauge pressure in the annular supply space during a 10-second rinse. A 16 mm internal diameter drain connects the bottom of the wash cavity to an opening in the outer cylinder.
A cylindrical parts rinse chamber drains through the outer cylinder into a sump fitted with a removable chip basket. A centrifugal pump draws from the sump and returns water through a cartridge filter to the outer cylinder inlet. Water in the annular plenum feeds chamber nozzles with ellipsoidal basin portions at their outlets. A float switch stops the pump when the sump level falls below the pump intake.
A through-beam photoelectric sensor spans the chamber entrance, and a controller operates a normally closed water valve at the outer cylinder inlet. When an inserted object interrupts the beam for 300 milliseconds, the controller opens the valve for eight seconds to feed the nozzles through the annular plenum. Each nozzle discharges through an outlet fed by an ellipsoidal basin portion, and runoff leaves through the chamber drain. After closing the water valve, the controller opens a separate low-pressure air valve for one second to clear residual water from the plenum and nozzles.
A bulkhead fitting passes through a radial hole in the outer cylinder and seals against a flat seating surface with an elastomer gasket. The fitting feeds the annular space around the inner cylinder, and a separate opening receives the drain tube.
The floor of the inner cylinder slopes at 3 degrees toward a 20 mm drain port fitted with a removable strainer. A drain tube runs downward through an aligned opening in the outer cylinder.
A molded polymer nozzle has a 1.5 mm entry bore that opens into a basin with an approximately ellipsoidal exit-side portion. At the exit aperture, that portion has an elliptical cross-section with full axes of 3 mm and 1.2 mm.
Each nozzle threads into a separate aperture in the inner cylinder and compresses a silicone O-ring beneath its shoulder. A round entry bore supplies the basin, whose exit-side portion follows an approximately ellipsoidal surface and meets the exit aperture at an elliptical cross-section.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
It will be appreciated that the ware washer will be in fluid flow communication with a source of water and will have a water inlet, wherein water is introduced into the washing cavity, and a water outlet, wherein dirty water is disposed of.A · US 2009/0199874 A1 · ¶ 41
Thus, in order to dispense it, the liquid or semi-liquid product is made to flow out of the tank 2 through the discharge orifice 3, enters the inlet orifice 5A and flows through the first cavity 7 of the tubular duct 6 (and out through the opening 8 and the release orifice 5B).B · US 2017/0208842 A1 · ¶ 56
The machine according to claim 9, wherein the tank has formed on the bottom of it an opening which is in fluid communication with the recirculation orifice of the tap and the outlet nozzle comprises a first, inlet portion having a first fluid flow section and being adapted to be coupled to the opening of the tank and a second, outlet portion having a second fluid flow section different from the first section.B · US 2017/0208842 A1 · claim 10
An empty cell means only that no passage was reproduced there.
Accordingly, warm water warewashing processes tend to lend themselves to at least some objectionable, unhygienic consequences.A · US 2009/0199874 A1 · ¶ 6
It is an object of the invention to provide an alternative ware washing process, that, it is believed, will overcome or at least minimize the disadvantages and difficulties with the prior art as set out above.A · US 2009/0199874 A1 · ¶ 8
Machines of this kind are known as “pasteurizers”, capable of mixing, cooking, pasteurizing, homogenizing, cooling, aging and storing under perfect conditions of hygiene, diverse speciality foods of the patisserie, ice cream and gourmet sectors.B · US 2017/0208842 A1 · ¶ 4
Hereinafter, this specification refers explicitly to these pasteurizers without losing in generality.B · US 2017/0208842 A1 · ¶ 5
patent.fyi, US 2026/0355759 A1, claim 1, first published 2026-11-19T14:56:45-05:00, https://patent.fyi/US20260355759/, SHA-256 97b76f784d50f20a466b8257745cf4e33454d0ba4274234b0149a1b2f15c7d1c