1.1Cylindrical rotor body
A cylindrical rotor turns in a matching bore, and spring-loaded port seals bear against its curved surface. A half-turn aligns the radial through duct with the same ports in reverse order for flushing.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A cylindrical rotor turns in a matching bore, and spring-loaded port seals bear against its curved surface. A half-turn aligns the radial through duct with the same ports in reverse order for flushing.
The insert enters from the inlet side and seats with its outlet face ground to match the spherical contour of the body. A seal ring bears on the spherical surface around the duct opening as the body turns between spray and flush positions.
A threaded retaining ring clamps a carbide spray plate against a flat face around the duct outlet. An annular gasket seals the joint and directs coating into the opening in the plate.
An electrical discharge machining operation cuts a fan-shaped spray opening directly into the hardened steel body. A perforated insert seated upstream divides the incoming flow into small streams that recombine in a chamber before reaching the spray opening.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A greenhouse irrigation boom carries reversible nozzles with spherical bodies, outlet-side pockets and round spray inserts seated in through ducts. Each nozzle pivots about a transverse stem, and a stamped deflector on the boom spreads its water jet over a seedling tray. At a drain station, the boom stops, the nozzle rotates 180 degrees, and manifold water enters the spray orifice and carries debris out of the connection opening into a trough.
A ground yttria-stabilized zirconia insert replaces a metal spray insert in the through duct of a spherical nozzle body. An internal shoulder and a threaded retaining collar capture the round insert from opposite sides, and a compression gasket seals between the insert and the shoulder. Three blind pockets in the outlet face sit outside the insert seat, and the insert remains captured when the body rotates to reverse flow.
A split rectangular housing with two opposed concave seat cartridges replaces the annular nozzle carrier. The housing clamps around a spherical nozzle body and supports its transverse pivot stem in bushings, while the cartridges align with the body through duct and bear against spherical bands outside the outlet-side pockets. In the spray position, one cartridge feeds the connection opening and the other passes the jet from the insert. A half-turn places the insert against the feed cartridge and routes the reverse discharge through the opposite cartridge.
A 12 mm diameter spherical body contains a 3 mm through duct that seats a round insert with a 0.25 mm spray orifice. Two 1 mm diameter blind pockets extend 0.5 mm into opposite sides of the outlet face and stay clear of the insert seat and the spherical sealing band. The head supplies an aqueous liquid at a nominal 0.3 MPa, and mechanical stops set the spray and reverse-flush positions 180 degrees apart.
A reciprocating conveyor spray carriage carries a reversible spherical nozzle with an outlet-side pocket and an insert in its through duct. At the end of carriage travel, a catch basin sits under the nozzle and a stationary actuator engages its transverse stem. A selector valve closes the coating feed and opens a rinse feed after the actuator reverses the nozzle, so the rinse enters the spray orifice and exits through the connection opening into the basin.
An upstream pressure transducer and a flowmeter monitor the supply to a reversible spherical nozzle with an outlet-side pocket and a spray insert. At a steady supply pressure, a controller initiates a cleaning cycle when flow stays below 80 percent of the stored clean-nozzle flow for two seconds. The controller closes the supply valve, vents the head and commands a geared motor to rotate the nozzle 180 degrees about its transverse axis. An end-position switch confirms alignment before the controller opens the valve for a one-second reverse pulse, then the controller closes the valve, vents the head and returns the nozzle to its spray position.
A stainless steel central part has a turned spherical surface and a through duct along the spray direction. A shallow milled pocket opens around the outlet end of the duct, with a radiused transition back to the spherical surface.
Two shallow flats are milled into the outlet half of the spherical central part on opposite sides of the duct opening. A band of spherical surface between the flats surrounds the opening and contacts the spray head seal.
A tungsten carbide insert seats against a shoulder near the outlet of the through duct, and a threaded retainer holds it from the inlet side. A narrow elongated opening in the insert forms a flat fan spray.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Unlike the prior art 30 in FIG. 3, this disk is not an integral part of the nozzle body 42. It is a totally independent component which is placed in a recess at the exit end of the nozzle.A · US 2011/0248095 A1 · ¶ 23
A method for providing adjustment of spray angle in a nozzle, comprising: providing a nozzle body for receiving a fluid supply thereto at an inlet thereof and for discharging the fluid supply, said nozzle body having an inner cavity for providing for fluid to swirl around the inner cavity; providing a receiving portion for an insertable orifice member for defining spray discharge orifice at a fluid outlet of the nozzle body; and inserting an orifice member into the receivingA · US 2011/0248095 A1 · claim 6
The inner orifice 200, as illustrated in FIGS. 1 and 2, is inserted to the inner orifice insertion hole 110 and coupled to the outer orifice 100, wherein the inner orifice 200 guides liquid contents moving in a form of water stream from the container body (not illustrated) to be sprayed smoothly.B · US 2017/0225178 A1 · ¶ 30
An empty cell means only that no passage was reproduced there.
In order to ensure the proper combustion and chemical recovery the liquor has to be atomized to an optimum droplet size.A · US 2011/0248095 A1 · ¶ 3
This enables one to fine tune the atomization to the specific combustion setup at that time and place.A · US 2011/0248095 A1 · ¶ 8
Due to this, an injection angel which is the most important among the elements of spray containers is not structured in the best fit for using according to its purpose, such that it is not possible to provide the best spray performance for each body part.B · US 2017/0225178 A1 · ¶ 3
Furthermore, it is characterized that an injection angle (K) is set to 40° when a diameter of the second injection hole 130 is set to 0.3 mm and a length of a spray orifice is set to 0.8 mm.B · US 2017/0225178 A1 · ¶ 8
patent.fyi, US 2026/0355773 A1, claim 1, first published 2026-11-19T15:20:40-05:00, https://patent.fyi/US20260355773/, SHA-256 007652b8d7c6b3cc957ebee7ac836ec861fea79a5eb98701f260b2184eed1d3b