1.1Integral upstream slot wall
Wire electrical discharge machining cuts a through-slot in a stainless steel body that contains both slot walls. A cross-drilled manifold supplies coating liquid along the width of the slot.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Wire electrical discharge machining cuts a through-slot in a stainless steel body that contains both slot walls. A cross-drilled manifold supplies coating liquid along the width of the slot.
A pump feeds a transverse manifold connected to closely spaced round bores in a dispensing bar. Liquid from adjacent outlets joins in the narrow gap between the bar and the moving substrate, forming a continuous bead across the coating width.
The die sits above the substrate and a backing roll supports it from below. A metering pump feeds liquid downward into the gap, where the moving substrate draws liquid from the bead to form a wet film.
A servo motor drives an endless belt through a straight coating span. Openings along the belt edges communicate with vacuum channels in a flat support shoe and hold the uncoated substrate margins while the center passes over the upward-facing slot.
A cylindrical grind forms the surface with its cylinder axis parallel to the slot width. The minimum clearance occurs at the crown, and the gap widens away from the crown in the direction of substrate travel.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Two die blocks beneath a backing roll form an upward-facing slot that feeds a waterborne acrylic primer onto the underside of a paper web. The roll carries the web with its axis on the second-block side of the plane defined by the upper part of the first die lip. A metering pump supplies the die manifold, and a downstream hot-air dryer removes water before the web is rewound.
A perforated vacuum drum replaces the solid coating roll and carries a porous textile web over an upward-facing slot formed between two die blocks. The drum axis lies on the second-block side of the plane defined by the upper part of the first die lip. A stationary internal vacuum sector grips the web upstream of the slot, and a vented sector equalizes pressure across the web at the coating bead. A servo drive turns the drum at the commanded web speed.
Two die blocks beneath a 100 mm diameter roll form a 100 mm wide upward-facing slot with a 150 µm opening. The first die lip runs 100 µm from the web at its closest point, and the roll axis lies 1 mm into the half-space facing the second die block, measured normal to the plane defined by the upper part of the first die lip. A metering pump delivers 10 mL/min onto a 120 mm wide web moving at 5 m/min, giving a nominal wet thickness of 20 µm across the 100 mm coated band.
An unwind station feeds a polymer web through a corona treater before the web reaches the coating roll. The treater electrode faces the surface that subsequently passes over the upward-facing slot between the two die blocks. The coating roll carries the treated surface across the slot with its axis on the second-block side of the plane defined by the upper part of the first die lip. A line encoder supplies web speed to both the corona power controller and the coating pump controller, which scale treatment power and liquid flow with speed.
Two die blocks beneath a coating roll discharge a waterborne adhesive upward onto the underside of a continuously moving polymer film. The coating roll axis lies on the second-block side of the plane defined by the upper part of the first die lip. The coated film passes through a hot-air dryer and enters a heated laminating nip with its adhesive face toward a second web from a separate unwind. Driven nip rolls press the webs together, and a downstream rewind collects the laminate.
Two die blocks form an upward-facing slot beneath a roll whose axis lies on the second-block side of the plane defined by the upper part of the first die lip. Infrared gauges upstream of the roll and downstream of the dryer measure absorption at a wavelength sensitive to the coating binder. The controller aligns the readings by web travel distance and uses a calibration curve to convert their difference to dry coat weight. A web encoder sets the base pump rate in proportion to web speed, and the controller trims that rate using the measured coat-weight error.
The second die block is machined from precipitation-hardened stainless steel and located by two ground dowel pins. Clamp screws compress a precision shim between the mating faces to set the slot opening.
A positive-displacement pump feeds a transverse distribution manifold below a 200 µm slot formed between the two blocks. The slot points vertically upward and supplies a bead beneath the substrate as a motor-driven coating roll advances it continuously.
The first die block terminates in an integral lip with a 0.5 mm-wide upper land. Grinding and lapping form a planar land across the coating width.
Matched ground shims at the two bearing mounts locate the roll axis 1 mm from the plane of the first lip's upper part, measured toward the second die block. The matching shim stacks preserve roll-axis alignment along the slot width.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The die 15 is constructed of a downstream block 21 and an upstream block 22.A · US 2007/0092655 A1 · ¶ 51
A forming tool includes at least one first die half where the first die half has an insert part which is designed to move a finished component out of the first die half along a direction of motion where a displacement direction of the insert part is inclined relative to the direction of motion.B · US 2020/0398330 A1 · abstract
According to one embodiment, the tool comprises the first die half and a second die half, which can be closed along a closing direction such that it is possible to form a cavity for a component, and wherein the displacement direction, at least to some extent, is inclined in relation to the closing direction and is oriented away from the cavity.B · US 2020/0398330 A1 · ¶ 5
The die 15 has a pocket 17 and a slot 18 between the downstream block 21 and the upstream block 22.A · US 2007/0092655 A1 · ¶ 51
The first lip is disposed downstream from the second lip in a feeding direction of the web. An end of the first lip is provided with a first lip land which is flat and confronted to the web.A · US 2007/0092655 A1 · ¶ 22
An empty cell means only that no passage was reproduced there.
The stripes and the non-uniformity become more remarkable when the thickness of the wet coating becomes smaller.A · US 2007/0092655 A1 · ¶ 5
Accordingly the unevenness in the coating is effectively prevented.A · US 2007/0092655 A1 · ¶ 9
In the case of the component having the surfaces which are plane-parallel in relation to the closing direction, it may be the case that the static friction is so high that it is no longer possible for the components to be removed manually or in an automated manner, for example using a robot.B · US 2020/0398330 A1 · ¶ 2
In other words, the insert part moves away from the component at least to some extent, which brings with it the advantage that the component can be removed from the insert part in a force-free manner, or without force being applied.B · US 2020/0398330 A1 · ¶ 4
patent.fyi, US 2026/0355778 A1, claim 1, first published 2026-11-19T15:20:40-05:00, https://patent.fyi/US20260355778/, SHA-256 b3ef7d4436c0efe0f592052518285e1e4192fd0fddba653ff996e5defadc65df