1.2Inboard pedestal supports
Welded steel pedestals connect each longitudinal member to transverse base beams. The longitudinal member extends beyond the pedestals and carries the hinge bearings on gusseted brackets at its ends.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Welded steel pedestals connect each longitudinal member to transverse base beams. The longitudinal member extends beyond the pedestals and carries the hinge bearings on gusseted brackets at its ends.
Bolted perforated steel panels span the lateral supports, which rest on coil springs. An eccentric shaft vibrates the inclined deck so smaller particles pass through the holes and larger particles travel to the discharge end.
A motor drives a train of meshing spur gears on the roller shafts, so each shaft turns opposite its neighbor. A drag conveyor above the rollers moves coarse material toward the discharge, and stationary combs at the downward-turning gaps hold coarse pieces above the nip while fines fall through.
Lower locating pins seat each panel in sockets on the frame, and captive latches secure the panel at the top. After releasing the latches, an operator lifts each panel by two recessed handles and places it in a storage rack.
Two vertically spaced bearings on one end upright carry the bulkhead on a vertical pin. A linear actuator swings the bulkhead sideways to expose the support and the area above it.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A metering belt feeds harvested carrots onto a roller screening module fitted with resilient polyurethane discs. The openings between adjacent rollers pass loose soil and smaller carrots into a lower chute, while the rollers carry larger carrots to an end discharge belt. The two bulkheads hang vertically clear of the lateral supports during grading and swing outward on hinges above the supports to expose the module sides for soil removal.
An electric worm gear reducer replaces the linear actuator on each bulkhead. The reducer mounts on one upright and drives a torque tube along the hinge axis, with the opposite upright supporting the tube in a bearing. Arms keyed to the tube swing the bulkhead outward to its inclined service position and return it to its vertical position. End-position switches stop the motor at each position, and a mechanical prop holds the bulkhead open during service.
A toothed belt replaces the chain transmission on the outer face of one lateral support. Each roller shaft carries a toothed pulley, and idlers on the smooth side of the belt press the toothed side around each pulley so all roller shafts turn in the same direction. A slotted idler sets belt tension, and the motor drives the loop through a separate toothed pulley. A fixed transmission cover fits inside the lowered bulkhead and is accessible when the bulkhead swings outward.
Three roller modules, each 1.2 m wide and 1.5 m long, sit end to end between shared longitudinal frame members. Short transfer plates bridge the joints, and each module has an external drive that turns all its rollers in the feed direction at 60 revolutions per minute. The clear openings increase from 20 mm to 35 mm to 50 mm along the feed path, and a separate chute under each module collects its undersize fraction. One bulkhead on each side covers all three lateral supports when lowered and swings outward to expose them together.
A crossbelt magnetic separator mounts above the conveyor that receives oversize material from the roller screen. The magnet lifts ferrous pieces from the moving material, and a transverse belt carries them into a side chute. The separator and chute stand downstream of the frame so both bulkheads swing outward through their full travel. A speed switch on the receiving conveyor stops the roller drive when the conveyor stops.
A safety controller receives signals from standstill monitors on the roller drive shafts and closed-position switches on both bulkheads. A service request stops the feeder and removes torque from the roller motors, and the controller enables the selected bulkhead actuator after confirming shaft standstill. The actuator raises the bulkhead about its overhead hinge until the open-position switch operates. The controller enables roller restart after both bulkheads indicate closed and the operator issues a separate reset.
The first and second sides are welded from rectangular steel tubing. Bolted crossmembers and diagonal braces tie the sides together and resist racking under uneven feed loads.
Each side carries a folded sheet steel bulkhead with hat-section ribs attached to its inner face. Hinge brackets connect each bulkhead to its side of the frame and support it in the lowered position.
The lowered bulkhead extends below the bottom edge of the lateral support and overlaps both ends of its outer face. Inward return flanges along the vertical edges overlap fixed end plates and close the end openings.
A stop limits outward rotation to 70 degrees from the lowered vertical position, and a captive pin secures the bulkhead at the stop. The inclined panel leaves the outer face of the lateral support and the space above it accessible from the side.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
This exemplary embodiment or another exemplary embodiment may further provide that the drainage system further comprises a removable false bulkhead operably engaged with the drainage portion, wherein the false bulkhead is independent from the bulkhead of the main body.A · US 2023/0242028 A1 · ¶ 7
The panel features a removable hatch through which workers can climb to access the interior of the blade.B · US 12,031,521 B1 · ¶ 66
An empty cell means only that no passage was reproduced there.
Over time, such spillage may cause unwanted stains or grime to build up on the trailer body giving the trailer an aesthetically displeasing appearance.A · US 2023/0242028 A1 · ¶ 3
The false bulkhead is provided to hide from public view any staining from the overflow of accumulated precipitation from a trough or other structure on the tank body.A · US 2023/0242028 A1 · ¶ 5
Accordingly, there is a need for a bulkhead removal system and method that can remove the bulkheads from the leading edge cavity of the blade.B · US 12,031,521 B1 · ¶ 4
The bulkhead removal device may provide that the adjustable support member is tapered to allow for the adjustable support member to collapse when the deployment assembly is pulled out of the wind turbine blade.B · US 12,031,521 B1 · ¶ 7
patent.fyi, US 2026/0355785 A1, claim 1, first published 2026-11-19T15:20:40-05:00, https://patent.fyi/US20260355785/, SHA-256 f3978fe14db309ac42a0d1c1e8e53b6955bafacf4e36a9fe285a002366a6a1b3